5
1800-065 Issued 1-19
Version D
PH LINE
16VAC
16VAC
E GND
POWER
POWER
SOURCE
SYSTEM A
PROGRAM
MASTER
CODE
NORMAL
DATA
RESET
LINK
SYSTEM B
ON/OFF
Button
Ethernet
1800-010
PH LINE
DATA OUT
BUSY OUT
BUSY IN
GROUND
DATA IN
DATA OUT
RS 232
RS 232
BUSY OUT
BUSY IN
GROUND
DATA IN
PH LINE
PH LINE
Cycle Power to the Cellular Module:
This will cycle power to the cellular module if power is ON or it will turn ON the module if it is OFF. This allows the module to re-connect with the cellular network.
Slide Switch to Program:
*
87 Master Code(Beep) 01
*
(Beep) 1
*
(Beep) to
cycle power
or 0
*
(Beep) to
NOT cycle power
.
Hang up Phone Slide switch back to Normal if done programming.
TCP/RS 232 Factory Defaults
This will RESET the TCP/RS 232 module back to factory defaults.
Slide switch to Program:
*
87 Master Code(Beep) 02
*
(Beep) 1
*
(Beep) to
reset defaults
or 0
*
(Beep) to
NOT reset defaults
.
Hang up phone. Slide switch back to Normal if done programming.
Cycle Power to Cellular Module Schedule:
This schedules the number of days between automatic power cycling of the cellular module. This allows the module to re-connect with the cellular network after
periods of non-usage. The revision letter of YOUR specific circuit board will restrict programming to either “number of days-Rev A ONLY” OR “number of hours-Rev B
or higher”.
“Rev A” Circuit Board ONLY, “0-9” number of days:
Note: 0= no cycle. 1= every day, 2= every two days, 3= every three days etc. Up to every 9 days.
Factory default setting: every 3 days.
Slide switch to Program
*
87 Master Code(Beep) 03
*
(Beep) 0-9
*
(Beep)
number of days
to cycle power.
Hang up phone. Slide switch back to Normal if done programming.
“Rev B or higher” Circuit Boards, “00-99” number of hours:
Note: 00= no cycle. 01= every hour, 02= every two hours, 03= every three hours etc. Up to every 99 hours.
Factory default setting: every 3 hours.
Slide switch to Program
*
87 Master Code(Beep) 03
*
(Beep) 00-99
*
(Beep)
number of hours
to cycle power.
Hang up phone. Slide switch back to Normal if done programming.
Number of Rings to Answer Call:
Sets the number of rings for an incoming call before the cellular system will answer. 2= two rings, 3= three rings, etc. Up to 9 rings. (2-9)
Normally the 1830 will answer on the second ring. In this case the cellular system will listen in for DTMF tones
*
87 Master code. If received, the cellular system will
stay on the line for programming while the 1830 will hang up. If any other DTMF tones are received, the cellular system will ignore them. If the 1830 does not answer
on the second ring, the cellular system will answer on the programmed number of rings.
Factory default setting: 5 rings.
Slide switch to Program
*
87 Master Code(Beep) 04
*
(Beep) 2-9
*
(Beep)
number of rings
before answering call.
Hang up Phone. Slide switch back to Normal if done programming.
TCP/RS 232 Power Cycle:
Sometimes it is necessary to cycle power to the TCP/RS 232 module to re-establish an Ethernet connection to the cellular module.
Slide switch to Program
*
87 Master Code(Beep) 05
*
(Beep) 1
*
(Beep) to
cycle power
to TCP/RS 232 module or 0
*
(Beep) to
not cycle power
.
Hang up phone. Slide switch back to Normal if done programming.
Multiple Program Note:
Once the
*
87 Master Code(Beep) has been keyed in and programming mode is entered, It is possible to program
multiple
functions without
leaving the programming mode. Just complete one program step and then go to the next.
Programming
Example:
Master Code is 1234. Cycle power to the cellular module and then cycle power to the TCP/RS 232 module.
*
871234(Beep) 01
*
(Beep) 1
*
(Beep) 05
*
(Beep) 1
*
(Beep) Hangup
Programming
PH LINE
SYSTEM A
RJ11
PHONE
JACK
PH LINE
DATA OUT
RS 232
BUSY OUT
BUSY IN
GROUND
DATA IN
PROGRAM
NORMAL
enter
programming
mode
exit
programming
mode
cycle
module
power
cycle
TCP/RS 232
power
The cellular system will remember the commands
received and execute them in order when program
mode is exited.
Program Slide Switch -
Slide this switch to program when programming the board LOCALLY
using a touch tone telephone. Be sure to switch back to Normal when finished programming.
Cellular voice will
NOT
work with program slide switch set to
PROGRAM
.
Setting the Master Code for Voice/Data Cellular System:
Slide switch to Program
Connect a touch tone phone to
System A
phone terminals. Press and release the Master Code push button. Enter on the phone the new 4 digit Master
Code and then press
*
. A tone should be heard in the phone ear piece. The new master code is now programmed. Hang up the phone to end programming.
Note: The cellular system’s master code
MUST
be the
SAME
as
System A
1830 master code. This is how the DKS cellular server identifies the cellular
system to contact it if needed. Set the slide switch back to Normal if done, or leave in Program if more programming will be done.
MASTER
CODE
Rev A
POW
SOUR
SYSTEM A
Circuit
Board
Revision
Letter
OR
Set program slide
switch to
NORMAL
for dial tone.
