25
DO917GDK
www.domo-elektro.be
DE
Reversing the Door Swing of Your
Beverage Cooler
Before Reversing the door ,the power must be shut off.
All parts removed must be saved to do the reinstallation of the door.
NOTE:
This beverage c
ooler has the capability of either opening the door from the
left or right side. The unit is delivered to you with the door opening from the
left side. Should you desire to reverse the opening direction, please follow
these instructions.
This beverage c
ooler has been built with the door hinges on the left. If you wish
to change the opening direction, follow the instructions below:
2. Remove the two screws (1) that hold the upper hinge (5) (right side) to the
frame. Take away the upper hinge (5).
3. Lift the door and place it on a padded surface to prevent scratching it.
5. Remove the two screws(8) that hold the lower hinge(2) and Make sure to
Remove the lower hinge(2).
6. Remove the left front leg (4) and transfer it to the right side.
7. Remove the hole cover plate(7) to the right side.
8.
Before placing this lower hinge(2), remove the bolt-pin (9) and reverse
the direction of the lower hinge(2). Then install the lower hinge (2) onto
the left side of the lower frame with two screws (8).
10. Set the door to its place making sure the door seat at the lower hinge(2)
.
11. While holding the door in the closed position secure the upper hinge (5) in the
top frame of left side with two screws (1). Please remember that do not tighten
the two screws(1) until the top of the door is levelled with the counter top.
1. Remove the upper hinge cover(6) first
12. Install the upper hinge cover(6) on the upper hinge..
9. Insert the bolt-pin(9) to the lower hinge (2).
4. Remove the two screws (10) that hold the handle (11) (on the right side frame).
Change the handle to the left side frame.
4
8
3
7
2
9
1
6
5
8
3
9
2
4
7
1
6
5
Door opening from left side
Door opening from right side
10
11
11
10
Page 15 from 20
15
1. Entfernen Sie die Abdeckung (6) der Scharniere.
2. Entfernen Sie die beiden Schrauben (1) des obersten Scharniers (5). Das Scharnier
entfernen.
3. Heben Sie die Tür hoch und legen Sie diese zur Vermeidung von Kratzern auf einen
weichen Untergrund.
4. Entfernen Sie die Schrauben (10) des Griffes (11). Versetzen Sie den Griff auf die andere
Seite.
5. Entfernen Sie die Schrauben (8) und das Scharnier (2) an der Unterseite der Tür.
6. Entfernen Sie den Stellfuß (4) und versetzen Sie ihn auf die andere Seite.
7. Versetzen Sie die Abdeckung der Bohrungen (7) auf der Oberseite des Kühlschranks auf
die andere Seite.
8. Bevor Sie das untere Scharnier (2) wieder montieren, entfernen Sie den Scharnierbolzen
(9) und ändern Sie die Scharnierrichtung. Setzen Sie das Scharnier (2) an der anderen
Seite wieder ein und schrauben Sie es mit den beiden Schrauben (8) fest.
9. Setzen Sie den Scharnierbolzen (9) in das Scharnier (2).
10. Setzen Sie die Tür auf das unterste Scharnier (2).
11. Halten Sie die Tür in geschlossenem Zustand fest und schrauben Sie das obere Scharnier
(5) mit den beiden Schrauben (1) fest. Kontrollieren Sie bei geschlossener Tür, dass die
Tür sowohl senkrecht als auch waagerecht ausgerichtet und die Dichtungen an allen
Seiten anliegen, bevor Sie das obere Scharnier (5) vollständig festziehen.
12. Setzen Sie die Abdeckung (6) wieder ein. Stellen Sie falls nötig die Stellfüße ein.
VERSETZEN DES GERÄTS
· Wen Sie das Gerät, unabhängig aus welchem Grund, ausschalten, warten Sie 10 Minuten,
bis Sie es erneut einschalten. Der Druck im Kühlsystem muss zunächst stabilisiert werden.
· Schalten Sie das Gerät aus und ziehen Sie den Netzstecker aus der Steckdose. Sämtliche
Lebensmittel entnehmen. Entfernen Sie außerdem alle abnehmbaren Teile (Regale,