background image

5

B.  Preparing The Awning Rail

 

Make sure awning rail is parallel to 

RV floor, and is

 NOT 

warped or curved before in-

stalling awning fabric. If awning rail is

 NOT 

straight, 

awning fabric may wrinkle or stretch.
Select the desired awning rail end (on the RV) into 

which the awning fabric will be inserted. Flare (wid-

en) that end of the rail with a flathead screwdriver, 

and remove (file) sharp edges. See FIG. 3.

If the awning is equipped with LED lights, flare 

the top (of the awning rail opening) 

ONLY

.

FIG. 3

Before

After

LED Awnings:

Flare Top Only

Typical Awnings:

Flare Top And Bottom

C.  Preparing The Awning For Installation

The awning requires minor preparation before in-

stalling on an RV.

1.  

Carefully lay the FRTA on a clean, well padded 

“V” trough (or other well protected surface) to 

prevent fabric damage.

2.  Insert the right hand top casting into the corre-

sponding main arm. See FIG. 4.

FIG. 4

RH Top Casting

1/4″-20 X 1/2″ 

Hex Head Screw

Main Arm

PREPARE FOR INSTALLATION

A.  Installing The Door Roller And Edge 

Guard (Optional)

 

Do

 NOT 

allow corner of entry door 

to contact awning fabric. Otherwise, premature 

wear or tearing of awning fabric could occur.
If there’s potential for a squared corner entry door 

to contact awning fabric, a door roller kit (NOT IN-

CLUDED) must be installed.

Rounded corner doors may

 NOT 

require a 

door roller kit if there is no potential for dam-

age to awning fabric.
See subsection, "A. Optional Components" 

on page (3) to order door roller kits.

1.  

Install the door roller. See FIG. 1.

a.  Place the door roller at the upper cor-

ner (opposite to hinge) of the outer entry 

door.  Face  the  roller  out,  and  1/4″  to  3/8″ 

(6.35 mm to 3.75 mm) above the door.

b.  Place and tighten the self-drilling screws 

(provided) through the mounting holes and 

into the door. 

FIG. 1

Position Wheel 

Directly Over 

Edge Of Door

Outer Entry 

Door

1/4″ - 3/8″

(6.35 mm - 

3.75 mm)

(Above Door)

2.  Clip the door edge guard onto the upper corner 

(opposite to hinge) of the inner screen door. See 

FIG. 2.

FIG. 2

Door Edge 

Guard

Inner Screen 

Door

Содержание SUNCHASER 8500














Отзывы: