background image

19

Draught-free installation

The refrigerator must be sealed in accordance with EN 1949.

Illustrated below is a typical approved method of sealing.

Proposal :

Using the Installation Sealing Kit from Dometic 
(available from Dometic)

Insert lipped seals (A) into the installation recesses at
the bottom and at each side (FIG 1, 2, 3).

Insert deflector plate (B), fitted with a lipped seal (A) of
heavy-duty, non- flammable material, into the
installation recess (see Fig. 4).

Insert deflector plate (B) in such a way that the hot air
escapes through the air vent grille into the open air.
Affix the discharge plate to the caravan wall, not to
the refrigerator !

In addition, discharge plate (B) with its lipped seal (A)
must seal the refrigerator off from the living area (see
FIG. 1,4).

Ensure that the refrigerator is installed level in the
recess.

Finally, push the refrigerator into the recess from the front.

This installation option facilitates the removal and installation of the appliance
for servicing.

Comment:

Other methods of sealing may be approved. However the chosen method must pre-
vent draughts entering the living space of the motorhome. Failure to seal correctly will 
allow warm air to collect around the refrigerator and its  performance will be affected.
If the cavity between the vehicle’s wall and the refrigerator is sealed so that fumes 
cannot penetrate the living area it is possible to vent the flue gas directly through the 
upper grille 
Do not use any kind of aluminium flue pipe (e.g. T-piece) to lead the flue gas out.

6.2

FIG. 1

FIG. 2

FIG. 3

FIG. 4

A

A

A

B

B

Deviations shall require the consent of the manufacturer.

Do NOT use any easily inflammable materials (in particular silicone sealing
agent or similar) for sealing! The device manufacturer's product liability
and guarantee shall lapse if such materials are used.

Содержание RM 7601 L































Отзывы: