Dometic Blizzard Turbo Скачать руководство пользователя страница 26

Страница: 26 / 32

TROUBLESHOOTING

Blizzard

Tur

bo Split System Manual

L-3448 ENGLISH

YSTEM

ROUBLESHOOTING

UIDE

NOTE: Internal fan (blower) is constantly on (unless in Power Saver mode); if not check all power connections.

Table 6: SYSTEM PROBLEMS AND SOLUTIONS

PROBLEM

SOLUTIONS

Unit does not operate at all. Internal fan
(blower) is not running.

1. If the Qt Control/Display is not on (all LEDs and data display window is

dark), follow instructions in the Quick Qt Control/Display Troubleshooting
Guide above.
a. Turn circuit breaker on or reset Qt Control/Display

b. Check to ensure that the Qt Control/Display is connected to a Q-Power

Logic Board (Qt Control/Display will not function with SMXII logic board)

c. Check CXP or TSEP cables and connections

d. Replace CXP or TSEP cables

e. Replace Qt Control/Display

f. Replace Q-Power Logic Board

2. If the Qt Control/Display is on, check the following:

a. Ensure that the generator is running at the correct frequency

b. Check that the batteries are fully charged

c. Check that the shorepower (if being used) is connected properly

d. Ensure the unit's circuit breaker is ON, and not tripped

e. Ensure that the inverter (if equipped) is connected properly and fuse/

breaker (DC and/or AC) is not tripped

Unit does not operate. Internal fan (blower) is
running.

1. Check that the Qt Control/Display is not in the OFF mode

2. Check the Qt Control/Display for fault/error code and follow Fault/Error

Code Troubleshooting Chart

3. Check the temperature setpoint to make sure it is sufficient for the unit to

operate in AUTO, COOL or HEAT modes

Unit does not make cold air.

1. Check the temperature setpoint to make sure it is sufficient for the unit to

cool

2. Check the evaporator air filter, clean as needed

3. Make sure switch is set to COOL

4. Make sure evaporator blower is running by checking for air flow from the

grill

5. Make sure that the condenser blower is running by checking for air flow

under the sleeper

6. Check the condenser coil while under the sleeper, clean as needed

7. Check the evaporator coil to make sure it is not frozen up (Note that

sometimes, during cool outside weather, and a low fan speed, the coil may
ice up. Turn the temperature setpoint so that the compressor cuts off and
turn the fan to maximum speed. Allow unit to defrost, then resume cooling.)

Содержание Blizzard Turbo

































Результаты поиска

Содержание Blizzard Turbo

Отзывы:

Похожие инструкции для Blizzard Turbo

Бренды по названию

Популярные бренды

Dometic Blizzard Turbo, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Blizzard Turbo

Отзывы:

Похожие инструкции для Blizzard Turbo

Бренды по названию

Популярные бренды