manualshive.com logo in svg

Dometic Blizzard NXT H541815A, Руководство по установке

Поделиться
Скачать
Dometic Blizzard NXT H541815A Скачать руководство пользователя страница 16

16

O.  (CCC 2 System Only) Furnace/Aqua 

Temperature Differential Setting

This system can be configured to operate using an 

ON//OFF differential of either 1 degree F or 2 de-

gree F. See (FIG. 34).

1.  To set the differential, simultaneously press 

the 

PROGRAM

 button and the   up button 

on the CCC 2 thermostat. “diF1” will appear in 

the display while the buttons are pressed. See 

(FIG. 34). To set the 2 degree differential, simul-

taneously press the 

PROGRAM

 button and the 

 down  button “diF2” will appear in the display 

while the buttons are pressed.

FIG. 34

9.  Remove Dometic cubes. 

Save Dometic cubes for future unit instal-

lations.

10.  Reinstall shroud.

M.  (LCD SZ System Only) System Checkout

1.  Verify that all features of the system work. See 

the LCD SZ thermostat Operating Instructions or 

User's Guide. Reconnect the 12 Vdc and 120 

Vac power supplies. Check fan speeds, cooling 

mode, heating mode, and furnace mode (if con-

nected) operation. 

If features do not work, disconnect the 120 Vac 

and 12 Vdc power supplies and verify that all 

wiring is correct. 

N.  (CCC 2 System Only) Reset & Checkout

1.  System Reset

After setting the dip switches in the electronic 

control, do a system reset.

a.  Re-connect the 12 Vdc and 120 Vac power 

supplies.

b.  Make sure the CCC 2 thermostat is in the 

OFF

 mode.

c.  Simultaneously press the 

MODE

 and 

ZONE 

buttons. The LCD will display "IniT" and all 

available zones.

d.  Release the 

MODE

 and 

ZONE

 buttons.

e.  Press the 

ON/OFF

 button to exit system set 

up.

f.  When a dip switch is turned on after initial 

configuration, a system reset will need to be 

done before the CCC 2 thermostat will rec-

ognize the updated selection.

2.  System Checkout

a.  Verify that all features of the installed sys-

tem work. See CCC 2 thermostat Operating 

Instructions or User's Guide. Check the fan 

mode, cooling mode, heating mode (if appli-

cable), and furnace mode (if applicable) op-

eration. If features do not work, disconnect 

the 120 Vac and 12 Vdc power supplies and 

verify that all wiring is correct and that the 

correct dip switches have been set to the 

"ON"

 position.

INSTALLATION INSTRUCTIONS

Содержание Blizzard NXT H541815A




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды