background image

4

999239002 - 07/2018 

Original Operating Instructions 

Framax stripping corner I hydraulic

Assembly

Carefully lay the stripping cylinder on its side.

Remove Spring cotter 5mm and Connecting pin 

10cm.

Remove the adapter from the cylinder.

Remove both pins D17.5.

Push the adapter into the pushrod of the stripping 

corner and pin it into position with two pins D17.5.

Place the stripping cylinder on the centring stud of 

the stripping corner.

The centring studs must be seated in the recesses of 

the assembly plate.

Twist the stripping cylinder clockwise until fully 

engaged.

Push the locking pin into the hole in the stripping cor-

ner.

Note:

The locking pin acts as anti-twist lock for the stripping 

cylinder.

NOTICE

 ▪

Stripping cylinders must always be fully 

retracted for installation.

 ▪

It is not permissible to install the stripping 

cylinder on a stripping corner that does not 

have a hole for the locking pin!
This hole is a standard feature of all strip-

ping corners manufactured from 2005 

onward.

 ▪

To prevent abrasion or trapping damage, 

the hydraulic hoses must be secured to the 

neighbouring formwork panel and properly 

laid and arranged. Tight bending radii 

should be avoided.

A

Spring cotter 5mm

B

Connecting pin 10cm

C

Adapter for Framax stripping corner I

D

Pin D17.5

C

Adapter for Framax stripping corner I

D

Pin D17.5

E

Push-rod

F

Framax stripping corner I

9239-200-11

D

9239-208-01

A

B

C

9239-200-05

C

D

E

F

NOTICE

It is not permissible to install the adapter in the 

pushrod with only one pin D17.5

G

Framax stripping cylinder I

H

Centring studs of stripping corner

I

Assembly plate

G

Framax stripping cylinder I

H

Centring studs of stripping corner

J

Locking pin

9239-200-04

H

G

I

9239-200-03

G

H

9239-200-09

J

Содержание 588614000



















Отзывы: