DOGTRA EXTENDED PRODUCT WARRANTY
EXTENDED LIMITED WARRANTY
For Certain Dogtra Products Purchased from Dogtra Authorized Dealers
FCC WARNING
The PATHFINDER complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. This is a sensitive radio device. Any unauthorized
changes or modifications to this device that are not expressly approved by Dogtra will void the warranty, and
may void the user’s authority to operate the equipment. Please do not tamper with or modify the unit.
Radio Frequency Radiation Exposure
This device is a mobile transmitter and receiver that uses an external antenna to send and receive low levels of
radio frequency (RF) energy for data communications. The device emits RF energy below the published limits
when operating in its maximum output power mode and when used with Dogtra Co. authorized accessories.
To comply with RF exposure compliance requirements, the device should be installed and operated with a
minimum of 8 inches between the device and your body. The device should not be used in other configurations.
* This device must not be co-located or operated in conjunction with any other transmitter or antenna.
Follow the steps below to code a PATHFINDER GPS connector
and GPS receiver.
2. GPS Receiver
1. To place the GPS receiver in pairing
mode, begin with the device turned off
and hold down the on/off button until
the LED light begins to rapidly blink
green.
2. A melody will play when the GPS
receiver is in pairing mode and emit
three beeps once it is paired.
1. GPS Connector
1. Start with the receiver turned off.
2. On the GPS connector, press the Select
button to turn the connector on and
press the Select button again to set it to
Collar mode.
* Setting the GPS connector to Phone
mode will pair the connector a
smartphone.
It has been tested and found to comply with RCM standards.
1+1 Year Extended Warranty
Except as otherwise provided, Dogtra warrants to the original retail purchaser (“You”) that your Dogtra
product shall be free of defects in materials and workmanship for a period of one (1) year from the date of
purchase (“Original Warranty”). As a special promotion, Dogtra further warrants that your Dogtra product
shall be free of defects in materials and workmanship for an additional one (1) year from the date that your
original warranty expires (“Extended Warranty”). The Original and Extended Warranties cover the cost of
repair (parts and labor) or replacement (if repair is not feasible) of a defective Dogtra product during said
warranty periods. For such repaired or replaced products, the remaining portion of the warranty periods, or
ninety (90) days, whichever is longer, shall apply. Dogtra, at its sole discretion, shall determine whether to
repair or replace a product covered by the Original Warranty or Extended Warranty.
Warranty Conditions
The Original and Extended Warranties are not transferrable and apply to your Dogtra product only if:
(1) You are the original retail purchaser of the product,
(2) You bought the product from a Dogtra Authorized Dealer, and
(3) You present a receipt or other proof of purchase showing a valid purchase date, the name and address of
the Dogtra Authorized Dealer, and the purchased product identified by model and/or serial number.
Warranty Exclusions
The Original and Extended Warranties do not cover damage, loss, or deterioration to your Dogtra product
caused: by misuse, neglect, abuse, or other improper handling of the product; by failure to follow use or care
instructions; by use of the product for other than its intended purpose; by accident or natural forces such as
fire or flooding; or by normal wear and tear such as scratches to the product surface.
The Original and Extended Warranties also do not cover Dogtra products that: are purchased from non-
authorized dealers; are purchased outside of the United States or Canada; have been damaged during
shipment (even if Dogtra paid or arranged for shipping); have been modified or tampered with in any manner;
are opened or repaired by anyone other than Dogtra; or have serial numbers that have been altered or
defaced.
3. Hold down the Connect button until the LED blinks rapidly.
Release the button.
4. Hold down the on/off button on the receiver until the LED light
begins to rapidly blink and plays a melody when the GPS
receiver is in pairing mode. Once paired, the receiver will emit
three beeps to show it has coded.
