manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

the odometer and trip odometer display is not shown
in the VFD. The unit of measure for the instrument
cluster odometer/trip odometer is selected at the time
that it is manufactured, and cannot be changed. Dur-
ing daylight hours (exterior lamps Off) the VFD is
illuminated at full brightness for clear visibility. At
night (exterior lamps are On) the VFD lighting level
is adjusted with the other cluster illumination lamps
using the panel lamps dimmer thumbwheel on the
headlamp switch. However, a “Parade” mode position
of the panel lamps dimmer thumbwheel allows the
VFD to be illuminated at full brightness while the
exterior lamps are turned On during daylight hours.
The VFD, the trip odometer switch, and the trip
odometer switch button are serviced as a unit with
the instrument cluster.

OPERATION

The odometer and trip odometer give an indication

to the vehicle operator of the distance the vehicle has
traveled. This gauge is controlled by the instrument
cluster circuit board based upon cluster programming
and electronic messages received by the cluster from
the Powertrain Control Module (PCM) over the Pro-
grammable Communications Interface (PCI) data
bus. The odometer and trip odometer information is
displayed by the instrument cluster Vacuum Fluores-
cent Display (VFD), and the VFD will not display
odometer or trip odometer information after the igni-
tion switch is turned to the Off position. The instru-
ment cluster circuitry controls the VFD and provides
the following features:

•

Odometer/Trip Odometer Display Toggling -

Actuating the trip odometer reset switch momen-
tarily with the ignition switch in the On position will
toggle the VFD between the odometer and trip odom-
eter display. Each time the ignition switch is turned
to the On position the VFD will automatically return
to the mode (odometer or trip odometer) last dis-
played when the ignition switch was turned to the
Off position.

•

Trip Odometer Reset - When the trip odome-

ter reset switch is pressed and held for longer than
about two seconds, the trip odometer will be reset to
000.0 kilometers (miles). The VFD must be display-
ing the trip odometer information in order for the
trip odometer information to be reset.

•

Message Failure - If the cluster fails to receive

a distance message during normal operation, it will
flash the odometer/trip odometer distance informa-
tion on and off repeatedly until a distance message is
received, or until the ignition switch is turned to the
Off position, whichever occurs first. If the cluster
does not receive a distance message within one sec-
ond after the ignition switch is turned to the On posi-
tion, it will display the last distance message stored

in the cluster memory. If the cluster is unable to dis-
play distance information due to an error internal to
the cluster, the VFD display will be blank.

•

Actuator Test - Each time the cluster is put

through the actuator test, the VFD will display all of
its characters at once, then step through each char-
acter segment individually during the VFD portion of
the test to confirm the functionality of the VFD and
the cluster control circuitry.

The PCM continually monitors the vehicle speed

sensor, then sends the proper distance messages to
the instrument cluster. For further diagnosis of the
odometer/trip odometer or the instrument cluster cir-
cuitry that controls these functions, (Refer to 8 -
ELECTRICAL/INSTRUMENT CLUSTER - DIAGNO-
SIS AND TESTING). For proper diagnosis of the
vehicle speed sensor, the PCM, the PCI data bus, or
the message inputs to the instrument cluster that
control the odometer/trip odometer, a DRBIII

t

scan

tool is required. Refer to the appropriate diagnostic
information.

OIL PRESSURE GAUGE

DESCRIPTION

An oil pressure gauge is standard equipment on all

instrument clusters. The oil pressure gauge is located
in the upper right quadrant of the instrument clus-
ter, above the fuel gauge. The oil pressure gauge con-
sists of a movable gauge needle or pointer controlled
by the instrument cluster circuitry and a fixed 90
degree scale on the cluster overlay that reads left-to-
right from “L” (or Low) to “H” (or High). An Interna-
tional Control and Display Symbol icon for “Engine
Oil” is located on the cluster overlay, in the center of
the gauge directly above the hub of the gauge needle.
The oil pressure gauge graphics are white against a
black field except for a single red graduation at the
low end of the gauge scale, making them clearly vis-
ible within the instrument cluster in daylight. When
illuminated from behind by the panel lamps dimmer
controlled cluster illumination lighting with the exte-
rior lamps turned On, the white graphics appear
blue-green and the red graphics appear red. The
orange gauge needle is internally illuminated. Gauge
illumination is provided by replaceable incandescent
bulb and bulb holder units located on the instrument
cluster electronic circuit board. The oil pressure
gauge is serviced as a unit with the instrument clus-
ter.

OPERATION

The oil pressure gauge gives an indication to the

vehicle operator of the engine oil pressure. This
gauge is controlled by the instrument cluster circuit

AN

INSTRUMENT CLUSTER

8J - 25

ODOMETER (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Бренд: iDataLink Страницы: 30
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
REVCAMUK MON16AHD Instructions preview
MON16AHD
Бренд: REVCAMUK Страницы: 4
kincrome K12071 Owner'S Assemble And Operating Manual preview
K12071
Бренд: kincrome Страницы: 6
ULTIMATE SPEED 94600 Assembly And Safety Advice preview
94600
Бренд: ULTIMATE SPEED Страницы: 21
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Бренд: Volvo Страницы: 262
Volvo 2006 XC70 Owner'S Manual preview
2006 XC70
Бренд: Volvo Страницы: 211
iArmor EDGE IA-W208 Manual preview
EDGE IA-W208
Бренд: iArmor Страницы: 6
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
Edelbrock 2917 Nstallation Instructions preview
2917 Nstallation
Бренд: Edelbrock Страницы: 1
POOL-LINE 110050 Assembly Instructions preview
110050
Бренд: POOL-LINE Страницы: 2
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Бренд: Whispbar Страницы: 63
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Бренд: Voxx Electronics Страницы: 15
Cadillac Escalade 2004 Escalade ESV Owner'S Manual preview
Escalade 2004 Escalade ESV
Бренд: Cadillac Страницы: 472
Lexus 2015 LX 570 Settings User Manual preview
2015 LX 570
Бренд: Lexus Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды