manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

(3) Install and tighten the four screws that secure

the instrument cluster to the instrument panel (Fig.
2). Tighten the screws to 2 N·m (17 in. lbs.).

(4) Reinstall the cluster bezel onto the instrument

panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - INSTALLATION).

(5) Reconnect the battery negative cable.

NOTE: Some of the indicators in this instrument
cluster are either programmable (upshift indicator)
or automatically configured (cruise, door and gate
ajar, gear selector indicator, service four-wheel
drive, overdrive-off, and transmission overtemp
indicators) when the cluster is connected to the
vehicle electrical system. This feature allows those
indicators to be enabled or disabled for compatibil-
ity with certain optional equipment. If a new instru-
ment cluster is being installed, use a DRBIII

T

scan

tool to program the instrument cluster with the
proper vehicle equipment option setting to enable
and/or disable the upshift indicator lamp. Refer to
the appropriate diagnostic information.

ABS INDICATOR

DESCRIPTION

An Antilock Brake System (ABS) indicator is stan-

dard equipment on all instrument clusters. This indi-
cator serves both the standard equipment Rear
Wheel Anti-Lock (RWAL) and optional equipment
4-Wheel Anti-Lock (4WAL) brake systems. The ABS
indicator is located in the Information Center area of
the instrument cluster, to the left of center. The ABS
indicator consists of a stencilled cutout of the Inter-
national Control and Display Symbol icon for “Fail-
ure of Anti-lock Braking System” in the opaque layer
of the instrument cluster overlay. The dark outer
layer of the overlay prevents the indicator from being
clearly visible when it is not illuminated. An amber
lens behind the cutout in the opaque layer of the
overlay causes the icon to appear in amber through
the translucent outer layer of the overlay when it is
illuminated from behind by a Light Emitting Diode
(LED) soldered onto the instrument cluster electronic
circuit board. The ABS indicator is serviced as a unit
with the instrument cluster.

OPERATION

The ABS indicator gives an indication to the vehi-

cle operator when the ABS system is faulty or inop-
erative. This indicator is controlled by a transistor on
the instrument cluster circuit board based upon clus-
ter programming and electronic messages received by
the cluster from the Controller Antilock Brake (CAB)
over the Programmable Communications Interface

(PCI) data bus. The ABS indicator Light Emitting
Diode (LED) receives battery current on the instru-
ment cluster electronic circuit board through the
fused ignition switch output (run-start) circuit when-
ever the ignition switch is in the On or Start posi-
tions; therefore, the LED will always be off when the
ignition switch is in any position except On or Start.
The LED only illuminates when it is provided a path
to ground by the instrument cluster transistor. The
instrument cluster will turn on the ABS indicator for
the following reasons:

•

Bulb Test - Each time the ignition switch is

turned to the On position the ABS indicator is illu-
minated by the cluster for about two seconds as a
bulb test.

•

ABS Lamp-On Message - Each time the clus-

ter receives a lamp-on message from the CAB, the
ABS indicator will be illuminated. The indicator
remains illuminated until the cluster receives a
lamp-off message from the CAB, or until the ignition
switch is turned to the Off position, whichever occurs
first.

•

Communication Error - If the cluster receives

no lamp-on or lamp-off messages from the CAB for
six consecutive seconds, the ABS indicator is illumi-
nated. The indicator remains illuminated until the
cluster receives a valid message from the CAB, or
until the ignition switch is turned to the Off position,
whichever occurs first.

•

Actuator Test - Each time the instrument clus-

ter is put through the actuator test, the ABS indica-
tor will be turned on, then off again during the bulb
check portion of the test to confirm the functionality
of the LED and the cluster control circuitry.

•

ABS Diagnostic Test - The ABS indicator is

blinked on and off by lamp-on and lamp-off messages
from the CAB during the performance of the ABS
diagnostic tests.

The CAB continually monitors the ABS circuits

and sensors to decide whether the system is in good
operating condition. The CAB then sends the proper
lamp-on or lamp-off messages to the instrument clus-
ter. If the CAB sends a lamp-on message after the
bulb test, it indicates that the CAB has detected a
system malfunction and/or that the ABS system has
become inoperative. The CAB will store a Diagnostic
Trouble Code (DTC) for any malfunction it detects.
Each time the ABS indicator fails to light due to an
open or short in the cluster ABS indicator circuit, the
cluster sends a message notifying the CAB of the
condition, and the CAB will store a DTC. For proper
diagnosis of the antilock brake system, the CAB, the
PCI data bus, or the message inputs to the instru-
ment cluster that control the ABS indicator, a
DRBIII

t

scan tool is required. Refer to the appropri-

ate diagnostic information.

AN

INSTRUMENT CLUSTER

8J - 13

INSTRUMENT CLUSTER (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

Qube AP1 Supplemental Instructions preview
AP1
Бренд: Qube Страницы: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Бренд: Cadillac Страницы: 32
Daihatsu F300 Service Manual preview
F300
Бренд: Daihatsu Страницы: 1718
Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Бренд: Air Lift Страницы: 12
WABCO TP2205 Installation Manual preview
TP2205
Бренд: WABCO Страницы: 48
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Бренд: Cadillac Страницы: 407
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Бренд: TATA Motors Страницы: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Бренд: Safe Fleet Страницы: 12
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Бренд: Subaru Страницы: 298
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Бренд: Honda Страницы: 124
Prorack K623 Fitting Instructions Manual preview
K623
Бренд: Prorack Страницы: 15
Ford Fusion 2019 Supplement Manual preview
Fusion 2019
Бренд: Ford Страницы: 51
OMNISTOR Omni-Bike Sport Ducato Installation preview
Omni-Bike Sport Ducato
Бренд: OMNISTOR Страницы: 5
Fleetwood Bounder turbo diesel 2001 Instructions Manual preview
Bounder turbo diesel 2001
Бренд: Fleetwood Страницы: 166
SIXTOL DRY CAR Instructions For Use Manual preview
DRY CAR
Бренд: SIXTOL Страницы: 32
APS iArmor IA-S159 Installation Instructions preview
iArmor IA-S159
Бренд: APS Страницы: 4
walser Crystalline Mounting Instruction preview
Crystalline
Бренд: walser Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды