Dodge 2011 Grand Caravan Скачать руководство пользователя страница 404 | Manualshive

Страница: 404 / 562

background image

The “Tire Pressure Monitoring Telltale Light” will flash
on and off for 75 seconds, and remain on solid when a
system fault is detected. The system fault will also sound
a chime. If the ignition switch is cycled, this sequence will
repeat, providing the system fault still exists. The “Tire
Pressure Monitoring Telltale Light” will turn off when
the fault condition no longer exists. A system fault can
occur with any of the following scenarios:

1. Jamming due to electronic devices or driving next to
facilities emitting the same radio frequencies as the TPMS
sensors.

2. Installing some form of aftermarket window tinting
that affects radio wave signals.

3. Accumulation of excessive snow and/or ice around
the wheels or wheel housings.

4. Using tire chains on the vehicle.

5. Using wheels/tires not equipped with TPMS sensors.

Vehicles With Compact Spare

1. The compact spare tire (if equipped) does not have a
TPMS sensor. Therefore the TPMS will not monitor the
pressure in the compact spare tire.

2. If you install the compact spare tire in place of a road
tire that has a pressure below the low-pressure warning
limit, upon the next ignition switch cycle, a chime will
sound, a

⬙

TIRE LOW PRESSURE

⬙

message will be dis-

played and the “Tire Pressure Monitoring Telltale Light”
will turn on.

3. After driving for up to 20 minutes above 15 mph
(24 km/h), the “Tire Pressure Monitoring Telltale Light”
will flash on and off for 75 seconds and then remain on
solid.

4. For each subsequent ignition switch cycle, a chime will
sound, the “Tire Pressure Monitoring Telltale Light” will
flash on and off for 75 seconds and then remain on solid.

402

STARTING AND OPERATING

«
...
402
403
404
405
406
...
»

Содержание 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2011 Grand Caravan

Бренд: Vauxhall Страницы: 323

Бренд: Romik Страницы: 6

Бренд: TATA Motors Страницы: 236

Бренд: Fast Master Products Страницы: 13

Бренд: Chevrolet Страницы: 428

Бренд: Subaru Страницы: 298

Бренд: Softride Страницы: 4

Бренд: Paccar Страницы: 63

Бренд: TAUBENREUTHER Страницы: 18

QuadraTop 11051.0415

Бренд: Quadratec Страницы: 8

Бренд: Packard Страницы: 25

Easy Air Auto Screen

Бренд: Wagan Страницы: 8

Бренд: Xingyun Страницы: 74

Бренд: Motoalliance Страницы: 4

Civic Hatch 2017

Бренд: Honda Страницы: 687

Бренд: ULTIMATE SPEED Страницы: 26

Бренд: Buick Страницы: 20

Directechs FORD11

Бренд: Directed Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды