DockCraft The DockSider 100 Series Скачать руководство пользователя страница 13

Страница: 13 / 14

Wood Dock with Decking Flush with Side Board

Wood Decking Flush with Aluminum Side Channel

Wood Decking – Pipe Dock

Page 13 of 14

Location #1 - 2 1/4 inches

Location #2 - 5 inches

Wood Decking Support

Ideal for situations when the

underside of your Dock is not

accessible

Floating Docks -

Hardware

- Standard Hardware

1/4 x 2 ½ inch Stainless Steel lag Screw

–

location #1, not included

- ¼ inch Stainless Steel washer, each location

Installation Requirements

Standard Installation; except

Location #1, Drill 1/8 or 3/16 inch pilot hole through decking and
into the wood decking support.

Insert Lag Screw and washers to secure.

Location #1 - 2 1/4 inches

Location #2 - 5 inches

Aluminum Decking Support

Hardware

- Standard Hardware

1/4 x 2 ½ inch Stainless Steel Cap Screw

–

location #1, included

- ¼ inch Stainless Steel washer, each location, included
- ¼ - 20 inch Stainless Steel nut and lock washer, not included

Installation Requirements

Standard Installation; except

Location #1, Drill 3/8 inch hole through decking and aluminum
decking support.

Insert Cap Screw , washer , and lock washer and nut to secure.

Location #1 - 2 1/4 inches

Location #2 - 5 inches

Hardware

1/4 x 2 ½ inch Stainless Steel lag Screw

–

location #1 & 2, not included

- ¼ inch Stainless Steel washer, each location

Installation Requirements

Location #1 & 2, Drill 1/8 or 3/16 inch pilot hole through decking and
into the wood decking support.

Insert Lag Screws and washers to secure.

Содержание The DockSider 100 Series















Результаты поиска

Содержание The DockSider 100 Series

Отзывы:

Похожие инструкции для The DockSider 100 Series

Бренды по названию

Популярные бренды

DockCraft The DockSider 100 Series, Инструкция по сборке, установке и эксплуатации

Результаты поиска

Содержание The DockSider 100 Series

Отзывы:

Похожие инструкции для The DockSider 100 Series

Бренды по названию

Популярные бренды