Dobot Magician Lite страница 14 Скачать руководство пользователя

Страница: 14 / 72

Dobot Magician Lite User Guide

Quick Start

Issue V1.9.1 (2020-01-11)

User Guide

2.2.4.2

Verifying the Dobot Driver

If an available COM port is displayed on the upper left corner of the DobotStudio page after

the robotic arm is powered on, as shown in Figure 2.12, the robotic arm driver is installed

successfully.

Figure 2.12 An available COM port is displayed

If no COM port is available, check whether the robotic arm driver is successfully installed by

following the steps below.

Figure 2.13 The robotic arm driver in the Device Manager window

Powering On/Off Magician Lite



Power on:

Press power button on Magician Lite or Magic Box, as shown in Figure

2.14. Once Magician Lite is powered on, all the stepper motors lock, and a short beep

sound will be heard, the LED indicator turns green. Now Magician Lite is ready to

use.

Содержание Magician Lite









































































Результаты поиска

Содержание Magician Lite

Отзывы:

Похожие инструкции для Magician Lite

Бренды по названию

Популярные бренды

Dobot Magician Lite, Руководство пользователя

Результаты поиска

Содержание Magician Lite

Отзывы:

Похожие инструкции для Magician Lite

Бренды по названию

Популярные бренды