doble TDR9000 Скачать руководство пользователя страница 56

Страница: 56 / 454

OCB/Motion

2-6

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

OCB/Motion

OCB and Motion are independent functions that are packaged together
for convenience.

The OCB portion of this module measures:

• Main Contact timing of Dead Tank circuit breakers
• Pre-insertion resistor switch timing
• Ohmic value of pre-insertion resistors (optional)

The Motion channels measure the linear or rotary movement of up to six
TR3190, 3160 motion transducers. The software accommodates:

• User-defined zones of measurement for calculating average

velocities

• Indirect contact measurements on transducers via a Linear

Transfer Function scaled by user-defined inputs

• English or Metric units

Figure 2.4 shows the available configurations for the OCB/Motion
module.

Figure 2.4 OCB/Motion Module Configurations

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 56 / 454

Результаты поиска

Содержание TDR9000

Отзывы: