doble TDR9000 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 454

doble TDR9000 Скачать руководство пользователя страница 55

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

2-5

Monday

, November 26, 2001 1:09 pm

TRXField

TRXField is installed on any laptop, or other
computer that is used to perform tests. It contains
the functionality to take existing Library Test Plans
and run them as individual Circuit Breaker Test
Plans.

TRXField offers the following capabilities:

• The creation of individual Circuit Breaker

Test Plans using a Library Test Plan as its basis.
Once completed, Individual circuit breaker
tests can be imported into the TRX software.
Each circuit breaker test adds to the database of
Test Results available for analysis using TRX.
These completed individual circuit breaker
tests contain not only the Test Results gathered,
but also a record of the Circuit Breaker Test
Plan used.

• The ability to view the results of an individual

circuit breaker test graphically and then tailor
the presentation of results to highlight
behaviors of interest.

• The ability to view the results in a tabular form,

then toggle back to the

Test

Plan

tab where

changes to the editable fields are actively
reflected on the

Tabulation

tab.

The main body of this guide explains the operations of the TRXField
software as it pertains to use with the TDR9000. Refer to ”TDR9000™
TRXField™ Software and Test Plan Dynamics” on page A-28 for a
complete explanation of TRXField fields and their uses.

Modules

There are four modules available that are installed in various
combinations by Doble when the system is ordered. The positions that
these modules occupy dictate the configuration of the boards in the
system backplane that support their operation. Once this configuration is
set, any field installation of newly purchased modules must be done in
accordance with Doble provided instructions.

The discussions that follow explain the module types, their purposes, and
their possible configurations.

«
...
53
54
55
56
57
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов