doble TDR9000 Скачать руководство пользователя страница 431

Страница: 431 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

I-21

Monday

, November 26, 2001 1:09 pm

Connect a flexible coupling between the threaded bar and the rotary
transducer. This coupling allows axial misalignment and transfers
rotary motion.

Connect the threaded bar with the flexible coupling and chuck at the
rotary transducer and tighten the two set screws.

The transducer with the flexible connector and the circuit breaker’s
shaft should be in line.

Tighten the moving bars.

The completed installation is shown in Figure I.20.

Figure I.20 Universal Adapter: Finished Installation

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 431 / 454

Результаты поиска

Содержание TDR9000

Отзывы: