manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 423 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 423

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

I-13

Monday

, November 26, 2001 1:09 pm

Figure I.7 shows a adapter/transducer combination that measures travel 
at the chain sprocket in the mechanism cabinet. A hex adapter (3/8" - 24 
to 8mm) is mounted on the TR3170 rotary transducer and is attached to 
the rotating element in the cabinet. The transducer hex adapter is 
attached to the rotating mechanism and then to the support plate. The 
support plate is the clamped to the structural plate in the cabinet using 
C-clamps.

Figure I.7  ABB HPL SF6 Gas Circuit Breaker – Chain Sprocket

Figure I.8 shows an adapter for use with the HVB SF6 Gas circuit 
breakers that uses a ganged operating mechanism. The adapter has a 
metric 16mm thread that treads into a tapped hole on the horizontal 
operator adjacent to pole 1 and the mechanism cabinet. This is shown 
with a 24" travel rod. 

Figure I.8  HVB SF6 Gas Circuit Breakers with 

Ganged Operating Mechanisms 

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов