doble TDR9000 Скачать руководство пользователя страница 325 | Manualshive

Страница: 325 / 454

doble TDR9000 Скачать руководство пользователя страница 325

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-125

Monday

, November 26, 2001 1:09 pm

Within the phase, the Dead time is calculated as the difference
between the time required for the last Main Contact to close and the
first Main Contact to open.

B

Dead Time with a Circuit Breaker

This is the time when at least one Main Contact
within the circuit breaker is open during the
reclose operation (Figure A.148).

Figure A.148 Reclose Operation within a Circuit Breaker

Contact #1

Contact #2

First to open

Last to close

Dead Time

0

A

#1

#2

#1

#2

0

B

0

C

«
...
323
324
325
326
327
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов