doble TDR9000 Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 454

doble TDR9000 Скачать руководство пользователя страница 321

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-121

Monday

, November 26, 2001 1:09 pm

Dwell Time

The callouts (

B

and

C

) in Figure A.144 on page A-122 show the

parameters and specifications that effect Dwell times for a breaker.

B

This is the time when all Main Contacts within a
phase are closed during trip-free operation
(Figure A.142).

Figure A.142 Trip-Free Test Operation for a Phase (Live Tank Breaker)

Within the phase, the Dwell time (Figure A.144 on page A-122) is
measured as the difference between the time required for the first
Main Contact to open and the last Main Contact to close.

C

This is the time when all Main Contacts within the
circuit breaker are closed during trip-free operation
(Figure A.143).

Figure A.143 Trip-Free Test Operation Within a Breaker

(Live Tank Breaker)

Contact #1

Contact #2

Last to close

First to open

Dwell
Time

0

A

Contact #1

Contact #2

Last to close

First to open

Dwell
Time

0

A

0

B

0

C

#1

#2

#3

#4

«
...
319
320
321
322
323
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов