doble TDR9000 Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 454

doble TDR9000 Скачать руководство пользователя страница 285

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-85

Monday

, November 26, 2001 1:09 pm

Figure A.98 shows how overtravel and rebound operate during a circuit
breaker opening operation.

Figure A.98 Overtravel/Rebound Open

Overtravel,
Rebound – Close

Parameters include:

Overtravel

The distance between the maximum temporary
displacement of the Circuit Breaker Main Contact
beyond the final closed position. Negative
tolerance for overtravel must never be greater than
the specified overtravel.

Rebound

The distance between the maximum temporary
displacement of the Circuit Breaker Main Contacts,
which is short of the final closed position. Negative
tolerance for rebound must never be greater than
the specified rebound.

Figure A.99 shows how overtravel and rebound operates for a circuit
breaker closing operation.

Figure A.99 Overtravel/Rebound Closed

Starting Closed

Overtravel

Rebound

Final Open
Position

Position

Starting Closed

Final Closed

Overtravel

Rebound

Position

Position

«
...
283
284
285
286
287
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов