doble TDR9000 Скачать руководство пользователя страница 284 | Manualshive

Страница: 284 / 454

doble TDR9000 Скачать руководство пользователя страница 284

Test Plan Items

A-84

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Figure A.97 shows timing for Total Travel and Contact Wipe.

Figure A.97 Total Travel and Contact Wipe Operation

Overtravel,
Rebound – Open

Parameters include:

Overtravel

This is the distance between the maximum
temporary displacement of the Circuit Breaker
Main Contacts beyond the final open position.
Negative tolerance for overtravel must never be
greater than the specified overtravel.

Rebound

This is the distance between the maximum
temporary displacement of the Circuit Breaker
Main Contacts which is short of the final open
position. Negative tolerance for rebound must
never be greater than the specified rebound.

Module #1

Module #1

Module #2

Module #1

Module #2

Module #2

#!

#2

#3

#4

#!

#2

#3

#4

Contact #1

Contact #2

Contact #3

Contact #4

0

A

0

C

0

20

40

60

Time (ms)

0

B

80

Travel 3

100

«
...
282
283
284
285
286
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов