manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 271 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 271

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

A-71

Monday

, November 26, 2001 1:09 pm

Main Contact 
Timing – Open

Parameters include:

Minimum

The minimum time for the Main Contacts to part.

Maximum

The maximum time for the Main Contacts to part.

Figure A.83 shows how contact timing occurs on a module-by-module 
level.

Module (A)

The maximum allowable difference in time 
between the opening of the two Main Contacts in 
any module.

Phase (B)

The maximum allowable difference in time 
between the opening of any two Main Contacts in 
a phase.

Breaker (C)

The maximum allowable difference in time 
between the opening of any two Main Contacts in 
a circuit breaker.

Figure A.83  Main Contact Timing – Open Breaker 

Module #1

Module #1

Module #2

Module #1

Module #2

Module #2

#!

#2

#3

#4

#!

#2

#3

#4

Contact #1

Contact #2

Contact #3

Contact #4

Main Contact
opening time

A

B

C

A

B

C

0

20

40

60

80

100

Time (ms)

First Switch to Last Switch

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов