doble TDR9000 Скачать руководство пользователя страница 265

Страница: 265 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-65

Monday

, November 26, 2001 1:09 pm

Table A.4 lists the test voltages used when testing Main Contacts.

If the command current range selected is too small for the actual current
applied, the current recorded in the masthead reads

*Over*

. The current

on the graphical output appears clipped. The performance of the test is
not affected (Figure A.77).

Figure A.77 Breaker Performance Report Header

Table A.4 Voltages Used When Testing Main Contacts

ITEM TESTED

RANGE SELECTION

TEST VOLTAGE

Resistor, EHV

10 – 300 Ohms

7.5 V

Resistor, EHV

200 – 500 Ohms

15 V

All without resistors

None

15 V

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 265 / 454

Результаты поиска

Содержание TDR9000

Отзывы: