doble TDR9000 Скачать руководство пользователя страница 255 | Manualshive

Страница: 255 / 454

doble TDR9000 Скачать руководство пользователя страница 255

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-55

Monday

, November 26, 2001 1:09 pm

Digital
Discriminator

For more information on the Digital Discriminator, see ”Understanding
Contact Measurement” on page A-22.

Test Duration
Parameters

The Instrument supports a recording length field where a recording
length is selected from a picklist. Each recording length has a sampling
rate associated with it. When a length is selected, the sampling rate
appears below it. Table A.2 lists the Recording Lengths and their
associated sampling rate.

The user-preferred recording length can be set using the TRX Options
window.

N

OTE

The Test Duration parameter is not available for the Capacitance test.

Table A.2 Recording Lengths and Sampling Rate

Recording Length

Sampling Rate

500 ms

10 kHz

1600 ms

10 kHz

10 s

1 kHz

30 s

500 Hz

1 min

200 Hz

5 min

50 Hz

20 min

10 Hz (Analog only)

«
...
253
254
255
256
257
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов