manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 218 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 218

Transient Recovery Voltage

A-18

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

Shunt Capacitor

Figure A.18 shows how a shunt capacitor is used to modify the TRV 
(Courtesy of ABB Power T&D Company, Inc.).

A shunt capacitor is connected across the phase-to-ground voltage. This 
has no effect on the magnitude of the recovery voltage but does affect the 
initial rate of rise of the transient voltage.

Figure A.18  Transient Recovery Voltage: Shunt Resistor Operation

Open-Gap Grading 
Capacitor

Figure A.19 shows how an open-gap grading capacitor is used to modify 
the TRV (courtesy of Mitsubishi Electric).

A capacitor is applied across the open contacts of a circuit breaker. Most 
multibreak circuit breakers use grading capacitors across the contacts to 
obtain the proper voltage division for interruption and surge voltage 
control.

The grading capacitor acts the same as a shunt capacitor in affecting the 
initial rate of the transient voltage.

Figure A.19  Transient Recovery Voltage: 
Open-Gap Grading Capacitor Operation

C

Z

TRV 
Shaping
Capacitor

C

Z

Grading
Capacitor

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов