doble TDR9000 Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 454

doble TDR9000 Скачать руководство пользователя страница 133

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-35

Monday

, November 26, 2001 1:09 pm

N

OTE

Make sure that the probe is not attached to, or placed near,
current-carrying wires during the zeroing process.

e. Click the

Probe Zero

button on the Virtual Front Panel.

The following message displays on the Virtual Front Panel:

Adjust probe until tone becomes constant. The process ends
automatically when the probe is correctly adjusted for
2 seconds.

f. Slowly adjust the thumbwheel on the top of the probe until

the modulated tone remains constant for two seconds.

When the probe reaches zero offset, the tone becomes steady.
If zero offset is maintained for two seconds, the tone stops and
the channel indicator turns green (Figure 4.14).

Figure 4.14 Probe Zero Indicator

g. Repeat this procedure for any additional probes.

N

OTE

If no activity is detected on the channel within 30 seconds, an error
message appears on the Virtual Front Panel. If the process fails, the
Probe Zero button remains red and the following error message
appears:

Process incomplete, Probe not zeroed

. Pressing OK removes

the error message, leaving the Probe Zero button red.

2.

Leave the probe on with the trigger locked in the ON position. Place
the range switch on the probe in the desired position.

N

OTE

Be careful not to disturb the thumbwheel.

3.

Securely clamp the probe around the wire that carries the current to
be monitored.

Probe Zero
Indicator

«
...
131
132
133
134
135
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов