doble TDR9000 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 454

doble TDR9000 Скачать руководство пользователя страница 122

Linear Transducer and Rotary Attachments

4-24

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Rotary Motion

To configure for rotary motion:

1.

Mount the Rotary Adapter onto the transducer by inserting the hex
shaft that extends from the back of the Rotary Chuck into the
hexagonal opening in the face of the transducer and align the three
captive screws (refer to Figure 4.11 on page 4-24).

2.

Tighten the captive screws.

Configuration is complete.

Figure 4.11 Rotary Adapter Mounted on Transducer

Linear Motion

To configure for linear motion:

1.

Remove the Rotary Adapter from the Transducer by loosening the
three captive screws.

2.

Store the Rotary Adapter in the Cable Bag to avoid damage.

Configuration is complete.

Captive

Captive
Screws

Screws

«
...
120
121
122
123
124
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов