doble TDR9000 Скачать руководство пользователя страница 114

Страница: 114 / 454

Linear Transducer and Rotary Attachments

4-16

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Linear Transducer and Rotary Attachments

This section discusses the configuration procedures for the TR3190
Digital Rotary/Linear Transducer and the TR3160 Motion Transducer.

Configuring the
TR3190

™

The TR3190 Digital Rotary/Linear Transducer is used to measure Rotary
or Linear motion. The setup for each measurement follows.

OTE

Early shipments of the TR3190 were marked externally as TR3160, but
were labeled as model TR3160LR on the S/N label.

Figure 4.4 shows the three components of the TR3190, which include:

• Transducer
• Chuck Holder Plate
• Rotary Chuck

The Chuck Holder Plate is mounted in different locations, depending on
whether a rotary or linear measurement is intended.

Figure 4.4 TR3190

™

(TR3160LR

™

) Transducer Components

Chuck Holder Plate

Transducer

Rotary
Chuck

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 114 / 454

Результаты поиска

Содержание TDR9000

Отзывы: