background image

 
 
 

 

 

 

 

4.  Pre-position the antenna to the correct azimuth and elevation  

 

 

 

 

coordinates by using a compass and inclinometer. 

 
 

 

 

5.  Pre-position the LNB to the indicated polarity setting. 

 
 

 

 

6.  Locate the DR500 Receiver within visual range of the antenna. 

 
 

 

 

7.  Connect a 75 ohm coaxial cable (RG-6, typical) from the output of   

 

 

the LNB to the Receiver RF IN connector. 

 
 

 

 

8.  Connect 120 VAC to 15VDC power adapter to the DR500   

 

 

 

 

Receiver – do not turn it on. (Or suitable alternate power source) 

 

 

Improvise a temporary sun shade over the DR500 front panel as the LED 
displays may be difficult to read in direct sunlight. 

 
 

 

 

9.  Place the receiver in signal strength mode by depressing channel   

 

 

up and channel down buttons simultaneously while the power is  

 

 

 

 

off.  Alternatively, this may be done with the remote control using    

 

 

 

Preset 180.  The display reads 

nL

, signifying it is not locked. 

 
 

 

 

 

— 

AUTH 

LED is Off unless the receiver is already authorized 

 
 

 

 

 

— 

SYNC 

LED is Off and remains so until the satellite is  

 

 

 

 

 

 

 

 

acquired 

 
 

 

 

The signal strength level numbers are preceded by a minus sign  
(-) to differentiate them from a music channel number.  Signal Quality 
readings vary from -00 (the strongest level) to approximately -80 
(weakest level) before losing the satellite lock 

nL

 

 

 

Rock the dish slowly from side to side and up/down around the nominal 
position.  When the Satellite has been located, the display will read out a 
negative number representing signal strength and the Sync light will 
illuminate.  Carefully move the dish to maximize signal, at which time the 
readout will be the least negative (closest to zero).  Tighten the bolts and 
check that signal strength has not been disturbed by tightening the bolts. 

 

 

Connecting Multiple Receivers to One Antenna 

 

Multiple DR500 Receivers can be connected to one antenna. However, to 
avoid damage to either the antenna LNB and DR500 Receiver, the 
following items must be used: 

 

 

 

 

 
 

Содержание Digital Audio Satellite Receiver DR500



































































Отзывы: