manualshive.com logo in svg

DMP Electronics Thinline 7563, Руководство по установке

Поделиться
Скачать
DMP Electronics Thinline 7563 Скачать руководство пользователя страница 4

2 

LCD Keypad Installation Guide

Installing the Keypad

All DMP keypad housings are designed to easily install on any 4” square box, 3-gang 

switch box, DMP 695 and 696 backbox, or a flat surface. Figure 1 shows the keypad 

housing base mounting hole locations.

Remove the Cover

The keypad housing is made up of two parts: the front, which 

contains the circuit board and keyboard components and 

the base. Use the following steps and figures to separate the 

keypad front and base.

1. Insert a flat screwdriver into one of the slots on the 

bottom of the keypad and gently lift the screwdriver 

handle toward you while pulling the halves apart. Repeat 

with the other slot.

2. Using your hands, gently separate the front from the base 

and set the front and components aside.

Harness Wiring

Figure 1 shows wiring harness assignments. Observe wire colors when connecting the 

red, yellow, green, and black wires to the keypad bus. Connect red to panel terminal 

7, yellow to terminal 8, green to 9, and black to panel terminal 10. Use 1k Ohm EOL 

resistors, DMP Model 311, on keypad zones 1 through 4.
The 7560/7560A keypads are supplied with a 4-wire harness for panel keypad bus 

connection.

The 7570/7570A and 7573/7573A keypads are supplied with a 12-wire data bus/zone 

harness. Four wires connect to the keypad bus. The remaining eight wires are for the 

four zone inputs: two wires for each zone.
The 7573/7573A keypads are supplied with one 5-wire output/reader harness.

Additional Power Supply

If the current draw for all keypads exceeds the panel output, provide additional 

current by adding a Model 505-12 auxiliary power supply. Connect all keypad black 

ground wires to the power supply negative terminal. Run a jumper wire from the 

power supply negative terminal to the panel common ground terminal. Connect all 

keypad power (+12 VDC) wires to the power supply positive terminal. Do NOT connect 

the power supply positive terminal to any panel terminal. Refer to the 505-12 Power 

Supply Installation Guide (LT-0453).

Lift screwdriver 

handle up 

toward you to 

separate keypad

cover from base.

Thinline

     or Aqualite

Keypad

Building Wall

Содержание Thinline 7563





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды