DMP Electronics CellCom SLC Скачать руководство пользователя страница 7

Страница: 7 / 40

CellComSL

Series Universal Communicator Installation and Programming Guide

Digital Monitoring Products

IntroductIon

CellComSL™ Series Universal Alarm Communicator

Description

The

CellComSL™ Series Alarm Communicator provides a fully supervised alarm communication path for any

burglary or residential fire control panel. The CellComSL Series can be connected to a control panel’s dialer

output and used to capture Contact ID messages

based on SIA DC-05-1999.09-DCS

. The CellComSLC has a

built-in CDMA cellular module to send messages to DMP Model SCS-1R or SCS-VR Central Station Receivers. The

communicator also provides four input zones and two open-collector outputs for connection to burglary or

residential fire control panel outputs and zones. The CellComSL Series Communicator Zone 4 allows a connection

to the bell output of an existing burglary control panel. The communicator operates in a variety of applications:

CID Dialer Connection, Zones 1-4 Input Connections, or Zone 4 Bell Connection (See Applications on page 5). The

CellComSL

™ Alarm Communicator includes an onboard Z-Wave controller for home automation applications.

What is Included

The

CellComSL Series Universal Alarm Communicator includes the following:

•  PCB with Enclosure
•  3.7 Vdc 800 mAh Lithium Ion System Battery
•  Hardware Pack

System Components

1.1

Terminals (J9)

Power Connection Terminals

Power is provided from the Nominal 12 Vdc auxiliary output of the burglary control panel.
OBSERVE POLARITY (See Figure 1 and Backlit Logo)
Using 18 - 22 AWG wire, connect the

communicator

te12 to the positive terminal on the

control panel

auxiliary output.

Connect the communicator terminal G (Ground) to the negative terminal on the control panel auxiliary output.

Control Panel Standby Power

During a power outage, the CellComSL draws power from the control panel’s backup battery. The CellComSL must

be included in the standby battery calculations for the control panel.

Zones 1-4

Terminals Z1 to Z3, G (Ground), Z4+ and Z4- provide four zones to connect to individual relay outputs on

the control panel. Zone 4 (Z4+ and Z4-) can be connected to the control panel bell output. See Zone 4 Bell

Connection.

Open-Collector Outputs

The two outputs, terminals O1 and O2 (see Figure 1), can be programmed to indicate the activity of the zones

Figure 1: CellComSL Series Communicator

RESET

LOAD

J19

J26

system components

Содержание CellCom SLC









































Результаты поиска

Содержание CellCom SLC

Отзывы:

Похожие инструкции для CellCom SLC

Бренды по названию

Популярные бренды

DMP Electronics CellCom SLC, Инструкция по установке и программированию

Результаты поиска

Содержание CellCom SLC

Отзывы:

Похожие инструкции для CellCom SLC

Бренды по названию

Популярные бренды