DMP Electronics Aqualite 7060A Скачать руководство пользователя

Страница: 6 / 28

LCD Keypad Installation Guide

Additional Power Supply

If the current draw for all keypads exceeds the panel output, you can provide

additional current by adding a Model 505-12 auxiliary power supply. Connect

all keypad black ground wires to the power supply negative terminal. Run a

jumper wire from the power supply negative terminal to the panel common

ground terminal. Connect all keypad power (+12 VDC) wires to the power

supply positive terminal. Do NOT connect the power supply positive terminal

to any panel terminal. Refer to the 505-12 Power Supply Installation Guide

(LT-0453) for more information.

Keypad Bus Monitor

For UL Listed fire protective systems, the 893/893A Module must be installed in

the XR500 Series or XR200 control panel to monitor the keypad bus and sound

an audible trouble whenever the keypad bus fails to operate. Refer to the 893/

893A Module Installation Sheet (LT-0135).

Card Readers

When a proximity credential is presented to an internal or external reader, a

beep tone is heard and the Power and Armed LEDs blink. This provides both an

audible and visual acknowledgement of the credential read.

Internal Access Control Reader

The 7063/7063A, 7073/7073A, and 793 keypads provide a built-in proximity

card reader designed to read HID 1300 Series proximity credentials.

Note: For UL Listed access control applications, the keypad must be

installed within the protected area.

External Access Control Reader

To accept Wiegand data input from HID, DMP, or other external card readers,

connect a 12 VDC external reader to the 7073/7073A or 793 keypad. Connect

the Red and Black power wires from the reader to the power wires from the

panel. These connect in parallel with the keypad power wires. Connect the

Reader (Data 1) wire to the White wire on the 5-wire keypad harness. Connect

the Reader (Data 0) wire to the Green/White wire on the 5-wire keypad

harness. See Figure 2.

Door Strike Relay Specifications

(7073/7073A, 793 only)

The 7073/7073A and 793 keypads provide one internal Form C single pole,

double throw (SPDT) relay for controlling door strikes or magnetic locks. Three

wires on the 5-wire harness, Violet (N/C), Gray (Com), and Orange (N/O), allow

you to connect devices to the relay. The Form C relay draws up to 15mA of

current and its contacts are rated for 1 Amp at 30 VDC maximum.

Содержание Aqualite 7060A





























Результаты поиска

Содержание Aqualite 7060A

Отзывы:

Похожие инструкции для Aqualite 7060A

Бренды по названию

Популярные бренды

DMP Electronics Aqualite 7060A, Руководство по установке

Результаты поиска

Содержание Aqualite 7060A

Отзывы:

Похожие инструкции для Aqualite 7060A

Бренды по названию

Популярные бренды