263H HSPA+ Cellular Communicator
Description
The 263H HSPA+ Cellular Communicator provides a fully supervised alarm communication path over the HSPA+ network. The 263H
is installed in the panel enclosure and powered by the panel, so no additional enclosure, power supply or battery back-up is
needed.
Compatibility
The 263H is compatible with XT30/XT50 Series panels (Version 112 or higher) that do not contain a built-in cellular modem and
XR150/XR350/XR550 Series control panels.
What is Included
The 263H includes the following:
• One Model 263H
• One SIM Card
• One Model 383 Rubber Duck Antenna
• One PCB standoff
Programming/Activation
Cellular Service is required before using the 263H for signal transmission. In Remote Link panel communication programming,
select Cellular as one of the Communication types. The 263H comes with a SIM card ready for activation with SecureCom
Wireless, LLC. More information is available at www.securecomwireless.com or refer to the Remote Link Users Guide (LT-0565)
or, use a SIM card provided by the carrier of your choice. If you are activating the unit with an alternate carrier, program the APN
provided by your carrier during panel programming.
Installation Safety
Ground Yourself Before Handling the Panel!
To discharge static, touch any grounded metal, such as the enclosure, before
touching the panel.
Remove All Power From the Panel!
Remove all AC and Battery power from the
panel before installing or connecting any modules, cards, or wires to the panel.
Installing the SIM Card
Insert the SIM
card into the 263H as pictured in Figure 1.
Installing the 263H
For XT Series:
1. Insert the PCB standoff end with flanges into the standoff hole in the panel PCB.
2. Hold the 263H at an angle and align the SMA antenna connector with the antenna
hole in the top of the panel enclosure.
3. Align the PCB standoff with the standoff hole in the 263H.
4. Press the 263H card 12 pin connector onto the
Cell Module (J24) connector on the panel while
applying even pressure to both sides of the board
to fully seat the module. See Figure 2.
For XR150/XR350/XR550 Series:
1. Insert the PCB standoff end with flanges into the
standoff hole in the panel PCB.
2. Align the PCB standoff with the standoff hole in
the 263H.
3. Press the 263H card 12 pin connector onto the
Cell Module (J24) connector on the panel while
applying even pressure to both sides of the board
to fully seat the module. See Figure 3.
Note:
If needed, the PCB can be removed from the enclosure to allow
placement of the cell module.
Connecting the Antenna
For XT Series:
Attach the included antenna to the SMA connector. See Accessories for
additional antenna options. Refer to Figure 2.
For XR150/XR350/XR550 Series:
1. Attach the 381-2 cable to the SMA connector.
2. Position one of the supplied washers onto the 381-2 SMA connector
and push the threaded end through an enclosure knockout.
3. Position the second washer onto the threaded end extending
through the knockout and secure the nut.
4. Attach the included 383 Antenna to the SMA connector. See Figure 3.
5. Attach the opposite end of the 381-2 Coax to the SMA connector on
the 263H. See Figure 3.
Note:
As an alternative, an antenna coax can be connected directly to the 263H SMA connector when
the coax enters the enclosure via conduit.
Antenna
Connector
SMA
Connector
PCB
Standoff
Cellular Antenna
enclosure hole
J3
Phone Line
Outputs
J11
1
2
3
4
J1
Ethernet
J16
Reset
J20
Wireless
Antenna
connection
J7 RJ
Supervision
263H
Figure 2: 263H Installation (XT)
65555
SIM
CARD
Bottom View
Figure 1: 263H SIM Card Installation
XR150/XR350/XR550
Panel
SMA
Connector
PCB
Standoff
263H
Nut
Washers
SMA
Connector
Antenna
Connector
Model 381-2
Coax Cable from
the 263H module
Figure 3: 263H Installation (XR150/XR350/XR550)
InstallatIon sheet
