DLE JETBOARD Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 39

DLE JETBOARD Скачать руководство пользователя страница 29

26

5.11 Please cut off the power if the board will not be used

More than 2 days.

5.12 Make sure the fuel tank is empty for transportation.

Use techniques - proper handling:

Shallow water

：

The water must be more than 50cm deep. Stand next

to the Jetboard, one knee on the board. One hand grabs the handle on the

hull. The other hand inserts the start key. After the engine is started, climb

onto the board when the speed is high enough so the Jetboard can support your weight.

Deep water

：

You should practice in shallow water before you go to deep water. When you fall off in the deep water area, do not try to climb onto

the Jetboard immediately. You should float on the side of board, grab the handle, insert the start key and start the engine. You should only climb

onto the Jetboard when the speed is high enough so the Jetboard can support your weight. (Always try to climb back to the board as fast as you

can when engine started, it will keep the water out of the cabin.)

«
...
27
28
29
30
31
...
»

Содержание JETBOARD








































Отзывы:

Нет отзывов