manualshive.com logo in svg

DLE DLE-85, Руководство оператора

Поделиться
Скачать
DLE DLE-85 Скачать руководство пользователя страница 7

7

Ignition Wire

(To Spark Plug)

Ignition Control Switch Wire 

(To On/Off Switch)

Pick-Up

Sensor Wire

(To Sensor

On Engine)

Tachometer Lead/

RPM Signal Output

ELECTRONIC IGNITION

SYSTEM

Battery Lead

Charge Lead

Switch 

(Not included)

Tachometer

(Not included) 

DLEG5525

OPTO Gas Engine Kill Switch

(DLEG9205, not included)

OPTIONAL

Ignition

Battery Lead

Ignition

Rx Batt

Lead

Rx

LED

KILL

SWITCH

Installing the DLE-85 on Your Airplane

Note:

 The DLE-85 must be installed on at least a 9.5mm [3/8"] 

thick 5-ply plywood fi rewall. The fi rewall must be securely glued to 
the airplane. Use triangle stock and pin the fi rewall with hardwood 
dowels to reinforce the fi rewall glue joints. Never install the
DLE-85 onto a fi rewall thinner than specifi ed because it may fail 
due to the power of the engine.

Note:

 The length of the engine from the back of the engine mount 

to the propeller drive washer is 7.87" [200 mm].

1

. Use the supplied template (on the back cover of this manual) to 

drill the engine mounting bolt holes.

2

.  Install (4) 5mm blind nuts on 

the back side (non-engine side of 
the fi rewall) in the holes drilled in 
step 1. 

3.

  Install the 8 grommets and 

4 spacers to the anitvibration 

mount as shown.

4.

 Install the 4 standoffs to the 

engine in the orientation shown 
using the (4) 5x20mm SHCS and 
5mm washers. Be sure to use 
threadlocker.

Содержание DLE-85

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды