manualshive.com logo in svg

DKT Comega IPLoC D2-POM-n, Быстрое руководство, Страница: 21 / 24

Поделиться
Скачать
DKT Comega IPLoC D2-POM-n Скачать руководство пользователя страница 21

IPLoC D2-POM-n - Mini Guide 2017-01-02. Ver. 1

Specifications are subject to change without notice. 

DKT is not responsible for any typographical errors or wrong.

Page 21

Device Configuration - Physical Mode

20/40 Coexistence:

Extension Channel:

Operating Mode:

Guard Interval:

Reverse Direction Grant(RDG)

Space Time Block Coding (STBC):

Aggregation MSDU(A-MSDU):

Auto Block ACK:

Decline BA Request:

HT Disallow TKIP:

Default is ”Disable”
You can choose between:
Enable and Disable

Default is ”Above”
You can choose between:
Above and Below

Default is ”Mixed Mode”
You can choose between:
Mixed Mode and Green Mode

Default is ”Auto”
You can choose between:
Auto and Long

Default is ”Enable”
You can choose between:
Enable and Disable

Default is ”Enable”
You can choose between:
Enable and Disable

Default is ”Enable”
You can choose between:
Enable and Disable

Default is ”Enable”
You can choose between:
Enable and Disable

Default is ”Disable”
You can choose between:
Enable and Disable

Default is ”Enable”
You can choose between:
Enable and Disable

When enables Reverse Direction Grant, the wire-
less AP can reduce the transmitted data packet 
collision by using the reverse direction protocol.

STBC is supported when the value is enable

MAC Service Data Unit (MSDU) aggregation group 
several data frames into one large frame. The 
concept of A-MSDU is to allow multiple MSDUs 
(MAC Service Data Units) to be sent to the same 
receiver concatenated in a single MPDU.

Decide whether Block ACK will be transmitted 
automatically.

Decide whether user wants to decline Block ACK 
request. 

Decide whether to operate in 802.11g, if using 
TKIP

The guard interval(GI) between symbols helps re-
ceivers overcome the effects of multipath delays.
802.11 a/b/g requires  GI to be 800 ns (Long). 

When 20/40MHz channel bandwidth has been set, 
the extension channel option will be enabled. 
The extension channel will allow you to get extra 
bandwidth.

Only use 20 Mhz / 40 Mhz combination if one of 
your devices require it.

The ”greenfield” mode is designed to improve 
efficiency by eliminating support for 802.11a/b/g 

devices in an all draft-n network. In green mode 
the network ignore all earlier standards.

Содержание IPLoC D2-POM-n

























Отзывы:

Нет отзывов