0
8
9
7
6
5
4
3
2
1
DISTANCE
SW2
SW1
2362-010
POWER
CONTROL
READER
1
12V
2
GND
3
D0
4
D1
5
TXD
6
RXD
8
GND
9
TRG
10
TRG
RESET
ON
3
GND
4
TRG
5
TRG
1
D0
2
D1
2
GND
1
12V
RED
BLUE
BLA
CK
BLA
CK
BLA
CK
YELLO
W
GRA
Y
WHITE
PURPLE
Wiring
DoorKing Part Number
1815-350
#1 Green - D0 (Data 0) to #11 Aux
#2 White - D1 (Data 1) to #12 Aux
#3 Black - Ground to #13 Aux
#5 Black - Ground - “Optional Loop Detector”
#4 Red - N.O. - “Optional Loop Detector”
12VDC
Power
DoorKing 1830 Telephone Entry System Circuit Board
Red - 12VDC
Normally Open
(N.O.)
Dry Contact
Relay
Black - Ground
NC
NO
RING
HF
1816
HS
ON
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
MIC
VOL
OFF
KEYPAD
3 2 1
3 2 1
3
2
1
MASTER
CODE
16AC
16AC
BAT
1NO
1NC
1C
2RY
2C
A
Z
IMC
5VDC
IMD
SPKR
COM
MIC
PSW
CGND
PHONE
1
2
3
12
34
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
Auxiliary
Terminal
Note:
500 ft
MAX
length.
DO NOT
use twisted wire.
Min
18 AWG
wire
100 ft
MAX
3 Amp
12VDC
“Optional” Trigger
Mode Wiring:
The
long range reader will
ONLY operate after the
trigger signal wires
have been activated by
a vehicle on the
in-ground loop.
Approximate
Antenna
Reading
Range
SW2 DIP-Switches 2-4 Settings
SW2 DIP-Switch 1 Setting
Use the rotary switch (SW1).
The reader will beep once
after each change of range. It
is also a good practice to put
the system into “test mode”
to benefit from the continu-
ous beeping feature while
adjusting the range.
Set the reader to eliminate redundant readings
of the same tag/card at certain time intervals
by using SW2 DIP-switches 2, 3 and 4 (
Note:
Switches 5-8 are NOT used).
Example:
If the
switches are set to: switch 2-
ON
, switch
3-
OFF
, switch 4-
ON
) the reader will read a
tag/card, beep and report it to the access
controller. For the next five (5) seconds, if it
reads the same tag/card again, it will ignore it.
It will not beep or report it to the access
controller.
Set for timing or trigger mode. See other side.
SW2 DIP-switches 2, 3 and 4
MUST
be set set to the
ON
position (right). This will put the
system in
test mode
. By choosing Timing/Trigger mode on DIP-switch 1, you can test in
either operating mode. Test mode is used to calibrate and adjust the maximum reading
range or maximum distance reader can read a tag/card. In timing test mode, reader sends
out read signals at a default rate of 10Hz. After each successful tag/card read, you will hear
a beep. As long as a tag/card is within range and in sight of the antenna, you will hear ten
beeps per second. This feature helps when adjusting the reader’s reading range, using the
rotary switch SW1. In “trigger” test mode, the same is achieved in the presence of a valid
trigger signal (car on loop).
Long Range Reader Control Board
Time Interval
Switch 4
Switch 3
Switch 2
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
0 sec (Test Mode)
1 sec
5 sec
10 sec
15 sec
20 sec
25 sec
30 sec
Switch 1 OFF - Timing Mode
Switch 1 ON - Trigger Mode
Test Mode
Switches 5-8
NOT used:
set to OFF
Position
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
SW1
0
1
2
3
4
5
6
7
8
9
8 ft
9.5 ft
11 ft
12 ft
13 ft
14 ft
17 ft
19 ft
21 ft
25 ft
#1 Red
#9 - Blue - Trigger Mode - for In-Ground Loop
#10 - Black - Trigger Mode - for In-Ground Loop
Orange
Brown
Not Used
#2 Black
#2 Black - Ground
#3 Yellow - D0 (Data 0)
#4 Gray - D1 (Data 1)
#5 Purple - TXD (Transmit Data)
#6 White - RXD (Receive Data)
Note:
Cable should be in
conduit for vandal protection.
Note:
The Blue and
Black wires are
ONLY
necessary if a in-ground
loop will be used
(Trigger Mode).
2-Conductor
Power Cable
9 ft
Antenna
Cable
Long Range
RFID Antenna
PW
R
DE
T
FA
IL
HIG
H
F
R
E
Q
LOW
RESE
T
FREQ
Vehicle
Lo
op
Detector
In-Ground
Loop
