djpower WP-2 Скачать руководство пользователя страница 3

 
WP-2 Bubble Fog Machine 
 

3 / 16

 

establish the correct electrical connection. All electrical and mechanical 

connections must be installed in accordance with European safety standards 
1.1. Intended use of the device 
This device is a device that was developed for professional use on stages, in 

discotheques, theatres, etc. The device is only approved for connection to a 

maximum of 230V, 50/60 Hz AC voltage and is only intended for indoor use. 
Regular breaks in use increase the service life of your device. 
Avoid physical shock or any form of violence when installing or starting up the 

device. 
Make sure that cables are not lying around freely. This would endanger your 

own safety and the safety of third parties. 
The device must not be operated or stored in an environment in which 

splashing water, rain or moisture is to be expected. Moisture or high humidity 

can reduce the insulation of the device and lead to fatal electric shocks. 
When using fog machines, it must be ensured that the fog saturation of the 

room must allow a good visibility of at least 10 m. 
Do not operate the device during thunderstorms. Overvoltage could destroy 

the device. In the event of a thunderstorm, completely disconnect the 

device from the mains by pulling out the mains plug. 
Surrounding objects or surfaces must not be touched by the housing. 
Make sure that when assembling and dismantling the device, the area below 

the assembly site is cordoned off. This also applies to the performance of 

service work. 
Familiarize yourself with the functions of the device before putting it into 

operation. Do not allow the device to be operated by persons who have no 

experience in it. The most common cause of malfunctions is improper 

operation of the device. 
Keep the device away from children and never operate it unsupervised. 
Never aim the nozzle at people and keep 50cm away from the nozzle. 

ATTENTION! The emitted mist is very hot. 
Keep a minimum distance of 50cm to other objects. 
Use only the recommended high quality water-based fluid from your dealer. 

Other fluids can cause damage. Do not use flammable additives such as oil, 

gas, perfumes, etc. in your fluid.  
Never point the nozzle at an open flame or flammable objects. 
Make sure to fill up the fluid in time. Running the machine without fluid can 

damage the pump and heater block. Unplug the power cord when topping 

up the fluid. 

Содержание WP-2

















Отзывы: