background image

36

MaIntenanCe

MAINTENANCE

Daily

At least 

once 
each 

year

Maintenance interval 

in hours

Before

After

25

50

100

300

Check/adjust throttle cable

Check the condition of belts, belt pulleys

Change the engine oil 

1)

Replace the engine oil filter

Clean/replace the spark plugs

Replace the fuel filter

Replace paper air filter 

2)

Check the caster wheels (every 200 hours)

Replace the air cleaner foam pre-filter 

2)

Check/adjust the mower deck

Check the engine valve clearance 

3)

Perform the 300-hour service 

3)

WARNING!
Before performing any service or 
adjustment checklist:
•  Engage the parking brake.
•  Place the Blade-switch in the 

disengaged position.

•  Turn the ignition switch to OFF 

position and remove the key.

•  Make sure the blades and all moving 

parts have completely stopped.

1)

 

First change after 8-10 hours. When operating with a heavy load 
or at high ambient temperatures, replace every 50 hours.

2) 

In dusty conditions, cleaning and replacement are required 
more often.

3) 

Performed by authorized service workshop.

 

= Described in this manual

 

= Not described in this manual

 

= Refer to the engine manufacturer's manual

Содержание 966698603





























































Отзывы: