dIXEL
Installing and Operating Instructions
1592026010
1592026010 XW40K GB R1.0 22.02.2008.doc
XW40K
5/5
Label Name
Range
Default Level
OE
Evaporator probe calibration
-12
÷
12°C /-120
÷
120°F
0.0 Pr2
P3P
Third probe presence (1st cond.
probe)
n=not present; Y=pres.
n Pr2
O3
Third probe calibration
-12
÷
12°C /-120
÷
120°F
0 Pr2
P4P
Fourth probe presence (2nd cond.
probe)
n=not present; Y=pres.
n Pr2
O4
Fourth probe calibration
-12
÷
12°C /-120
÷
120°F
0 Pr2
OdS
Outputs activation delay at start up
0÷255 min.
0 Pr2
AC
Anti-short cycle delay
0÷30 min.
1 Pr1
Ac1
Second compressor delay
0÷255s
5 Pr2
rtr
P1-P2 percentage for regulation
0 ÷ 100 (100=P1 , 0=P2)
100 Pr2
CCt
Compressor ON time during fast
freezing
0 ÷ 23h 50 min.
0.0 Pr2
CCS
Set point for continuous cycle
(-55.0÷150,0°C)
-5 Pr2
COn
Compressor ON time with faulty probe
0÷255 min.
15 Pr2
COF
Compressor OFF time with faulty
probe
0÷255 min.
30 Pr2
DISPLAY
CF
Temperature measurement unit
°C ÷ °F
°C
Pr2
rES
Resolution (integer/decimal point)
in ÷ de
dE
Pr1
rEd
Remote display
P1 ÷ 1r2
P1
Pr2
dLy
Display temperature delay
0 ÷ 20.0 min (10 sec.)
0 Pr2
dtr
P1-P2 percentage for disply
1 ÷ 99
50 Pr2
DEFROST
tdF
Defrost type
EL, in
EL Pr1
dFP
Probe selection for defrost termination
nP; P1; P2; P3; P4
P2 Pr2
dtE
Defrost termination temperature
-50,0÷110°C / -58÷230°F
8.0
Pr1
IdF
Interval between defrost cycles
1÷120h
6
Pr1
MdF
(Maximum) length for 1° defrost
0÷255 min.
30
Pr1
dSd
Start defrost delay
0÷99min
0 Pr2
dFd
Displaying during defrost
rt, it, SEt, dEF, dEG
it Pr2
dAd
MAX display delay after defrost
0÷255 min.
30 Pr2
Fdt
Draining time
0÷60 min.
0 Pr2
dPO
First defrost after start up
n ÷ y
n Pr2
dAF
Defrost delay after fast freezing
0 ÷ 23h 50 min.
0.0 Pr2
AUXILIARY
THERMOSTAT
ACH
Kind of action for auxiliary relay
CL; Ht
cL Pr2
SAA
Set Point for auxiliary relay
-50,0÷110°C / -58÷230°F
0,0 Pr2
SHy
Differential for auxiliary relay
0,1÷25,5 °C / 1÷45°F
2,0 Pr2
ArP
Probe selection for auxiliary relay
nP / P1 / P2 / P3
nP Pr2
Sdd
Aux.output working during defrost
n, y
n Pr2
ALARMS
ALP
Probe setting for temperature alarm
P1÷P4
P1 Pr2
ALC
Temperature alarms configuration
rE÷Ab
rE Pr2
ALU
MAXIMUM temperature alarm
-50,0÷110°C / -58÷230°F
10,0 Pr1
ALL
minimum temperature alarm
-50,0÷110°C / -58÷230°F
10,0 Pr1
AFH
Temperature alarm and fan differential
0,1÷25,5 °C / 1÷45°F
2,0 Pr2
ALd
Temperature alarm delay
0÷255 min.
15 Pr2
dAO
Delay of temperature alarm at start up
0 ÷ 23h 50 min.
1,3 Pr2
AP2
Probe for temperat. alarm of
condenser
nP; P1; P2; P3; P4
P4 Pr2
AL2
Condenser for low temperat. alarm
(-55 ÷ 150°C) (-67÷ 302°F)
-40 Pr2
AU2
Condenser for high temperat. alarm
(-55 ÷ 150°C) (-67÷ 302°F)
110 Pr2
AH2
Differ. for condenser temp. alar.
recovery
[0,1°C ÷ 25,5°C] [1°F ÷ 45°F]
5 Pr2
Ad2
Condenser temperature alarm delay
0 ÷ 254 (min.) , 255=nU
15 Pr2
dA2
Delay of cond. temper. alarm at start
up
0.0 ÷ 23h 50’
1,3 Pr2
bLL
Compr. off for condenser low
temperature alarm
n(0) - Y(1)
n Pr2
AC2
Compr. off for condenser high
temperature alarm
n(0) - Y(1)
n Pr2
AUXILIARY
OUTPUT
tbA
Alarm relay disabling
n=no; y=yes
y Pr2
oA3
Fourth relay configuration
ALr = alarm; dEF = do not select it;
Lig =Light; AUS =AUX; onF=always
on; Fan= do not select it; db = do
not select it; dF2 = do not select it
Lig Pr2
AoP
Alarm relay polarity (oA3=ALr)
oP; cL
cL Pr2
DIGITAL
INPUT
i1P
Digital input polarity
oP=opening;CL=closing
cL Pr1
i1F
Digital input configuration
EAL, bAL, PAL, dor; dEF; Htr, AUS
dor Pr1
did
Digital input alarm delay
0÷255min
15 Pr1
Nps
Number of activation of pressure
switch
0 ÷15
15 Pr2
odc
Compress and fan status when open
door
no; Fan; CPr; F_C
F-c Pr2
rrd
Regulation restart with door open
alarm
n – Y
y Pr2
HES
Differential for Energy Saving
-30°C÷30°C; -54°F÷54°F
0 Pr2
OTHER
PbC
Kind of probe
Ptc; ntc
1 Pr2
Adr
Serrial address
1÷247
ntc Pr1
onF
on/off key enabling
nu, oFF; ES
oFF Pr2
dP1
Room probe display
--
- Pr1
dP2
Evaporator probe display
--
- Pr1
dP3
Third probe display
--
- Pr1
Label Name
Range
Default Level
dP4
Fourth probe display
--
- Pr1
rSE
Current set point
-
Pr1
rEL
Software release
- - -
1,1 Pr2
Ptb
Map code
- - -
- Pr2
dIXEL
S.p.a.
Z.I. Via dell’Industria, 27 - 32010 Pieve d’Alpago (BL) ITALY
tel. +39 - 0437 - 98 33 - fax +39 - 0437 - 98 93 13
http://www.dixell.com
E-mail:
