manualshive.com logo in svg

Ditch Witch 420sx, Руководство оператора

Поделиться
Скачать
Ditch Witch 420sx Скачать руководство пользователя страница 98

420sx Operator’s Manual

Service - 97

Recommended Lubricants/Service Key

Recommended Lubricants/Service Key

Proper lubrication and maintenance protects Ditch Witch equipment from damage and failure. Service 
intervals listed are for minimum requirements. In extreme conditions, service machine more frequently. 
Use only recommended lubricants. Fill to capacities listed in See “Specifications” on page 129.

For more information on engine lubrication and maintenance, see your Deutz

®

 engine manual.

Item

Description

DEO

Diesel engine oil meeting API service classification CF-4 or E1-96 and SAE viscosity 
recommended by engine manufacturer   (SAE 15W40)

MPG

Multipurpose grease meeting ASTM D217 and NLGI 5

MPL

Multipurpose gear oil meeting API service classification GL-5  (SAE 80W90) 

THF

Tractor hydraulic fluid, similar to Phillips 66 HG, Mobilfluid 423, Chevron Tractor 
Hydraulic Fluid, Texaco TDH Oil, or equivalent  

Check level of fluid or lubricant

 Check 

condition

Filter 

Change, replace, adjust, service, or test

NOTICE: 

  

•

Use only genuine Ditch Witch parts, filters, and approved lubricants to maintain warranty. 

•

Use the “Service Record” on page 139 to record all required service to your machine.

Содержание 420sx














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды