Ditch Witch 420sx Скачать руководство пользователя страница 130

Страница: 130 / 141

420sx Operator’s Manual

Specifications - 129

420sx

Specifications

420sx

Dimensions *

U.S.

Metric

Overall height, ROPS upright

91 in

2.31 m

Overall height, ROPS folded down

71 in

1.80 m

Overall height, trenching boom fully raised (2’ boom w/
chain)

75 in

1905 mm

Transport length without plow blade

123 in

3.12 m

Transport length with 18” plow blade

142 in

3.61 m

Transport length with 18” plow blade and trencher with 2’
boom

192 in

4.88 m

Length, plowing with trencher attachment

156 in

3.96 m

Wheelbase

46 in

1.17 m

Width, 26x12-12 tires

47.8 in

1.21 m

Width, 23x10-12 tires

42.5 in

1.08 m

Width, dual tires

62 in

1.57 m

Ground clearance

5.5 in

140 mm

Angle of departure with 18” (457 mm) blade

22.5°

Angle of approach with 18” (457 mm) blade

22.5°

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды