Ditch Witch 420sx Скачать руководство пользователя страница 73

Страница: 73 / 141

Trench - 72

420sx Operator’s Manual

Setup

CMW

Setup

1. Fasten and adjust seat belt.

2. Start tractor. See page 50 for start-up procedures.

3. Drive to starting point. Move in line with planned trench. See page 52 for operating procedures.

4. Engage parking brake.

5. Lower boom to just above ground.

6. Check that attachment speed is in the LOW position.

7. Check that boom is in line with planned trench.

EMERGENCY SHUTDOWN -

Turn ignition switch to STOP.

Crushing weight could cause death or serious injury. Use proper

procedures and equipment or stay away.

NOTICE:

Use attachments or counterweights to make front and rear loads balance when all

attachments are raised. Contact your Ditch Witch dealer about counterweights for your equipment.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

NOTICE:

Comply with all utility notification regulations before plowing, digging or drilling.

Incorrect procedures can result in death, injury, or property damage.

Learn to use equipment correctly.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды