DirecTV Advanced Installation Meter 2 Скачать руководство пользователя страница 103

Страница: 103 / 108

Page 103

AIM 2 Operation Manual

Transferring records from a USB flash drive to the AIM

Insert the USB flash drive in the appropriate

USB connector on the meter.

2. Press

CONFIG

to go to the

CONFIGURATION

screen.

3. Highlight

Records

and press

SELECT

to go

to the

RECORDS MAIN

screen.

4. Highlight

Transfer Records from USB

and

press

SELECT

to go to the

TRANSFER

RECORDS FROM USB

screen. Then

highlight one of the following options:

• To copy an individual record, highlight

Select Individual Record

and press

SELECT

. Highlight the record to copy

and press

SELECT

• To copy all records from the USB

drive, highlight

Copy All Records

and press

SELECT

• To copy all records of a selected type

from the USB drive, highlight the

type of records to copy and press

SELECT

On the message that appears to confirm your transfer, press

6. The records are transferred to the AIM, and the

RECORDS MAIN

TRANSFER

RECORDS FROM USB

screen appears.

You also can view, move, or delete an individual record from

the Options screen. Press OPTIONS, highlight the desired

option, and press OK.

Содержание Advanced Installation Meter 2













































































































Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды

DirecTV Advanced Installation Meter 2, Руководство по эксплуатации

Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды