background image

 

DSEFO144-12 Rev 8/19 

Directive Systems & Engineering 

                     2702 Rodgers Terrace

 

              Haymarket, VA 20169-1628 

                             www.directivesystems.com 
                                      703-754-3876 

 

12 Element 2.5 wl. K1FO Designed Yagi, Model DSEFO144-12 

                                                                 

 

ELECTRICAL SPECIFICATIONS 

 

        Frequency range: MHz ...................... 144-146 

Gain: dBd...........................................  12.6 
Impedance: Ohms.............................. 50 
Connector type................................... Type N(F) UG-58/U 
Front -to- back ratio: dB...................... 23 
SWR: Typical at resonance................ 

1.2:1 

Beamwidth: degrees 

E- Plane ................................. 34° 
H- Plane ................................. 37° 

Sidelobe level: decibels 

E- Plane ................................. -19 
H- Plane ................................. -16 

Power rating, Continuous: Watts ......  1000 
Stacking Distance: ft.(m) 

E- Plane.................................. 

11’7” (3.53) 

      

         H- Plane................................. 

10’8” (3.25) 

 

MECHANICAL SPECIFICATIONS 

 

Boom length: ft. (m.)........................... 

17’4” (5.28) 

Turning radius: in. (m.)........................ 

10’4” (3.15) 

Weight Assembled: Lbs (kg.).............. 9.5 (4.32) 
Max mast size: in. (cm.)....................... 2

” (5.08) 

Wind surface area: Ft (m. ) ................. 1.5 (.14) 
Wind Survival: Mph (km/hr)................. 100 (160) 
 

PARTS LIST 

                                     

Note: All hardware is Stainless Steel, unless otherwise noted. 

 

Содержание DSEFO144-12











Отзывы: