Directed SMARTSTART ASRA-2510 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 26

Directed SMARTSTART ASRA-2510 Скачать руководство пользователя страница 13

User guide

P.13

Activating

Idle

mode (Automatic Transmission):

1. With the engine running, make sure to release the brake pedal and

press the

,

or

button on the transmitter

until the parking lights come

ON

.

Note:

SmartStart™ can be setup to use the

icon to activate

Idle

mode,

Turbo

mode or

Ready

mode.

2. Remove the ignition key from the ignition switch.

The engine will continue running.

3. Exit the vehicle. All doors, the hood and trunk should be closed

4. Press the

button to lock the doors, to arm the starter kill and to

arm the alarm. The engine will be kept running at idle speed.

a. When re-entering the vehicle, the user must reinsert the key into

the ignition and turn it to the

ON

position (not Crank) without

pressing on the brake.

b.

Once the key is in the

ON

position

, press on the brake pedal to put

the transmission in gear.

c.

Drive off.

If your vehicle has a

manual transmission

,

Idle

mode can be activated through

the same routine as that used for

Ready

mode (page 9); at the last step, the

button is pressed instead of the other buttons. This will lock the

doors, arm the system and leave the engine running.

NEW FEATURE

–

Push-To-Start

Idle

Mode

This feature is a variation of

Idle

mode, but made specifically for Push-To-Start

vehicles, with automatic or manual transmissions. (Consult your installer for

availability of this feature.) Follow the same steps as the normal Idle Mode

procedure, except for when re-entering the vehicle while the engine is running;

1. Close all doors.

2. You have 1.5 minutes (or 3 minutes) to press on the brake pedal, to get

in gear and drive off.

«
...
11
12
13
14
15
...
»

Содержание SMARTSTART ASRA-2510



























Отзывы:

Нет отзывов