© 2012 Directed. All rights Reserved.
2
QRN4115V 2012-09
Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
1.
Turn
the ignition on, then off.
2.
Select
a Menu. Within 10 seconds,
Press
and
hold
the Valet button. The number of LED flashes and horn
honks indicates the menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2
honks indicates menu 2.
3. When the desired menu LED flashes and honks are heard,
release
the Valet button.
4.
Select
a Feature, within 10 seconds.
Press
and
release
the Valet button the number of times correspond-
ing to the feature you wish to change. Then
press
and
hold
one more time to select the feature. The LED
flashes and the horn honks to indicate which feature is selected.
5.
Program
the Feature. While holding the Valet button, you can program the feature using the remote
control.
Pressing the button on the remote control advances to each feature option. The LED flashes and the horn honks
indicating which option is selected.
Once a feature is programmed:
•
Other features can be programmed within the same menu
•
Another menu can be selected
•
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1.
Press
and
release
the Valet button the number of times necessary to advance from the feature you just pro-
grammed to the next one you want to program.
2. Then
press
the Valet button once more and
hold
it.
To select another menu:
1.
Press
and
hold
the Valet button.
2. After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
•
The ignition is turned On
•
There is no activity for 30 seconds
•
The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These additional features and the adjust-
ments that may be programmed are described in the table below.
Menu Item
Feature
Default
Options
1
Engine Runtime
12 min.
1-60 min.
2
Diesel start type
Off
Timed
3
Diesel start delay time (seconds)
15 sec
1-90 sec.
4
Virtual Tach Fine Tune
Not initialized
0 to 1 second in 50 millisecond
increments
5
Remote control programming
Unlocked
Locked
6
Feature Programming
Unlocked
Locked
Feature Menus
Default settings are in
bold
type.
Menu 1
Feature #
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
1
Horn function
Off
Siren
20 mS
Siren
30 mS
Siren
40 mS
Siren
50 mS
2
Ignition con-
trolled lock
On
Off
3
Ignition con-
trolled unlock
On
Off
4
Doorlock out-
put duration
0.8 sec.
3.5 sec.
0.4 sec.
5
Double pulse
unlock
Off
On
6
Double pulse
lock
Off
On
7
Factory Alarm
Disarm func-
tion
with unlock
Before unlock Remote start
only
8
Factory Alarm
Disarm Pulses
Single
Double
9
Comfort*
Closure
Comfort
Closure 1
Off
Comfort
Closure 2
10
Panic*
On
Off
*Option not available on 1- button
Menu 2
Feature #
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
1
Engine check-
ing
Virtual tach
voltage
Off
tachometer
2
Engine
Runtime
12 min
24 min
60 min
3
Park light
output
Pulsed
Constant
4
Cranking time
0.6 sec.
0.8 sec.
1.0 sec.
1.2 sec.
1.4,
1.6,
1.8,
2.0,
4.0 sec
5
Activation
pulse count
1 pulse
2 pulses
3 pulses
6
2nd Ignition
behavior
Ignition
Accessory
7
Accessory
output
Off during
wait-to-start
On during
wait-to-start
8
2nd Status
behavior
Normal
Latch rear
defogger
Pulse rear
defogger
9
Anti-grind
On
Off
10
Diesel start
delay
Off
Timed 15 sec
Timed 30 sec. Timed 45 sec.
11
Timer mode-
run time *
12 min
3 min
6 min
9 min
*Option not available on 1- button
Remote Programming
1. Turn key to the ON position
2. Within 10 seconds, press and release Valet button one time.
3. Within 10 seconds, press and hold the Valet button. The LED will flash one time and the horn honks (if con-
nected) to confirm entry into remote programming. Do not release the valet button.
4. Press the button on the remote control. The horn honks to confirm the remote has been programmed.
5. Release the Valet button.
6. Turn the key to the Off position. The horn sounds one long honk to confirm that remote programming has
been exited.
The programming routine exits if any of the following occurs:
•
The ignition is turned off
•
There is no activity for 30 seconds
•
The Valet button is pressed too many times
Basic Remote Functions
Button Press
Function when remote
start is OFF
Function when remote
start is ON
Press for less than 1.5 seconds
Start the engine
Unlock doors
Press for more than 1.5 seconds Car finder
Stop the engine
Reset and Deletion
If a feature/virtual tach needs to be reset or the remote controls need to be deleted, use the following procedure.
1. Turn the ignition to the ON position (The heavy gauge pink wire must be connected).
2. Within 10 seconds, press and release the Valet button: 2 times if you want to delete remotes, 3 times to
reset features or 4 times to reset virtual tach. These features are described next.
Delete remotes:
This feature erases all remotes from the memory of the system. This is useful in cases
when a customer’s remote is lost or stolen.
Note: This does not reset the programmed features of the system or reset the Virtual Tach setting.
Reset Features:
This resets all features of the system to the factory default settings.
Note: This feature does not delete the remotes from the system or reset the Virtual Tach setting
Virtual Tach Reset:
Deletes all previously learned values for Virtual Tach, and on the next remote start
sequence the unit begins virtual tach initialization.
Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach setting.
3. Once you have selected the function step, press the Valet button once more and hold it. The LED flashes and
the horn honks to confirm the selected functional step. Do not release the Valet button.
4. While holding the Valet button, press the button on the remote control. The horn honks to confirm that the
feature has been successfully reset. You can now release the Valet button.
Additional information can be
found at:
www.directechs.com
