© 2012 Directed Electronics. All rights Reserved.
2
QRNDSS5003 2012-01
Programming System Features
Note:
When doing any programming with security features off, the horn function
(feature menu 1 item 13) must be programmed as Siren function to get an audible
confirmation from the unit.
The System Features Learn Routine dictates how the unit operates. It is possible to
access and change most of the feature settings using the control center button.
1.
Open
a door.
2.
Turn
the ignition on, then off.
3.
Select
a Menu.
Press
and
hold
the control center button. The number of siren
chirps indicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu
2 and 3 chirps for menu 3.
4. When the desired menu chirps are heard,
release
the control center button.
5.
Select
a Feature.
Press
and
release
the control center button the number of
times corresponding to the feature you wish to change. Then
press
and
hold
one more time to select the features.
6.
Program
the Feature. While holding the Control center button, you can
program the feature using the remote control.
For features with only two options;
AUX
= option 1 while
AUX
= option 2.
For features with more than two options;
AUX
selects the options in ascending order.
Once a feature is programmed:
•
Other features can be programmed within the same menu
•
Another menu can be selected
•
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1.
Press
and
release
the control center button the number of times necessary to
advance from the feature you just programmed to the next one you want to
program.
2. Then
press
the control center button once more and
hold
it.
To select another menu:
1.
Press
and
hold
the control center button.
2. After 3 seconds, the unit advances to the next menu and the siren chirps, indi-
cating which menu has been accessed.
The learn routine exits if any of the following occurs:
•
The open door is closed
•
The ignition is turned On
•
There is no activity for 30 seconds
•
The control center button is pressed too many times
Security Features Disable/Enable
The system has the ability to function as a security/remote start system or keyless/
remote start system by enabling or disabling security. The default setting is Enabled.
To program the feature.
1. Open a door.
2. Turn the ignition on, then off.
3. Press and hold the control center button until the LED flashes 3 times and the
siren (if connected) chirps 3 times.
4. Release the control center button.
Note:
If the control center button is released and then pressed again, the sys-
tem will enter the features programming menus.
5. Within 15 seconds, simultaneously press the
AUX
and
AUX
buttons of a pro-
grammed remote control.
6. The siren (if connected) will chirp and the parking lights will flash as listed
below
1 flash/chirp: Security features disabled
2 flashes/chirps: Security features enabled
Security Features Disabled will disable all security operations of the system, includ-
ing but not limited to those listed below:
•
Multi Level Arming
•
Sensor Warn-away
•
Full Trigger Operation
•
Armed While Driving
•
Automatic Engine Disable
Note:
Disabled features with programmable options can still be programmed manu-
ally or with the Bitwriter but will not operate until the Security Features have been
enabled.
The Security Features Disable/enable routine exits if the following occurs:
•
The open door is closed
•
The ignition is turned on
•
There is no activity for 15 seconds
•
The control center button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or un-
locked. If the learn routine has previously been locked, it must be unlocked
with Bitwriter® - this cannot be done manually with the control center but-
ton.
The Bitwriter®
gives you access to a wider range of system options. These
features and the adjustments that may be programmed are described in the table
below.
Menu
Item
Feature
Default
Options
1
Siren Duration
30 sec.
1-180 sec.
2
Aux 2 Timed Output
30 sec.
1-90 sec.
3
Aux 3 Timed Output
30 sec.
1-90 sec.
4
Aux 4 Timed Output
30 sec.
1-90 sec.
5
Engine Runtime
12 min.
1-60 min.
6
Diesel Start Delay
15 sec.
1-90 sec.
7
Timer Mode Runtime
12 min.
1-16 min.
8
Virtual Tach Fine Tune
Not initialized
0-1000 in 50 millisecond increments
9
Transmitter Programming
Unlocked
Locked
10
Feature Programming
Unlocked
Locked
Note:
The “Zap” feature on the Bitwriter does not reset the Virtual tach or security
features enabled/disabled settings
Red 4-pin port, Bitwriter/ESP2 or D2D programming
The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port.
The factory default is Bitwriter/ESP2 mode.
To use as D2D mode follow the below steps:
1. Make sure White/Blue activation wire is grounded.
2. Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode
change.
3. Remove the White/Blue wire from ground.
To change from D2D to Bitwriter/ESP2 mode:
1. Make sure the White/Blue activation wire is grounded.
2. Power the unit up, the system LED turns on solid for 5 seconds to confirm Bit-
writer/ESP2 mode change.
3. Remove the White/Blue wire from ground.
The procedure can be repeated to toggle from one mode to the other.
Important:
If you power up the system with the White/Blue activation
wire ungrounded, the system LED will come on solid for 5 seconds indi-
cating the system is in Bitwriter/ESP2 mode.
Feature Menus
Default settings are in
bold
type.
Menu 1 - Basic
Menu
Item
One-chirp setting
Two-chirp setting
1
Active Arming
Passive arming
2
Arm/disarm chirps on
Arm/disarm chirps Off
3
Ignition lock On
Ignition lock Off
4
Ignition unlock On
Ignition unlock Off
5
Active locking only
Passive locking
6
Panic with ignition On
No panic with ignition On
7
0.8 second door lock pulses (1)
3.5 (2), 0.4 (3) seconds
8
Forced passive arming on
Forced passive arming off
9
Automatic engine disable on
Automatic engine disable off
10
Armed When Driving (AWD) On
AWD Off
11
Code Hopping On
Code Hopping off
12
Horn Output Pulsed
Constant
13
Horn function Full Alarm Only (1)
Siren function - chirp length
20ms (2), 30ms (3), 40ms (4), 50ms (5)
14
Comfort Closure ON (1)
Comfort Closure OFF
(2)
Comfort Closure 2 (3)
Menu 2 - Advanced
Menu
Item
One-chirp setting
Two-chirp setting
1
30 second siren duration
60 second siren duration
2
Nuisance Prevention Circuitry On
Nuisance Prevention Circuitry OFF
3
Progressive door trigger
Instant door trigger
4
Disarm from Valet, 1 pulse
Disarm from Valet, 2-5 pulses
5
Door trigger error chirp ON
Door trigger error chirp OFF
6
Ignition controlled domelight On
Ignition controlled domelight OFF
7
Unlock output 1 pulse
Unlock output 2 pulses
8
Lock output 1 pulse
Lock output 2 pulses
9
Factory disarm with trunk release
ON
Factory disarm with trunk release OFF
10
FAD function with Unlock (1)
Before Unlock (2), Remote Start only (3)
11
FAD 1 pulse
2 pulses
12
AUX 2 validity (1)
Latched (2), Latch reset with ignition
(3), 30-secs timed (4), 60-secs (5),
90-secs (6)
13
AUX 2 Linking None (1)
Arm (2), Disarm (3), Remote Start (4)
14
AUX 3 validity (1)
Latched (2), Latch reset with ignition
(3), 30-sec. timed (4)60sec(5)90sec(6)
15
AUX 3 linking None (1)
Arm (2), Disarm (3), Remote Start (4)
16
AUX 4 validity (1)
Latched (2), Latch reset with ignition (3),
30-sec. timed (4) 60sec (5) 90 (6)
17
AUX 4 linking None (1)
Arm (2).Disarm (3), Remote Start (4)
Menu 3 - Remote start
Menu
Item
One-chirp setting
Two-chirp setting
1
Engine checking: Virtual Tach
Voltage(2), OFF(3), Tachometer(4)
2
Remote start runtime: 12 min
24 min, 60 min
3
Parking light output:
Flashing
Constant
4
Cranking time: 0.6 sec
0.8, 1.0, 1.2, 1.4, 1.6, 1.8, 2.0, 4.0
second
5
Activation pulse 1
2
6
2nd Ignition/Acc output: Ignition
Accessory
7
Acc state during wait-to-start Off
On
8
2nd status output: Normal
Rear defogger: latch 10 min.
rear defogger pulse
9
Anti grind:
On
Off
10
Diesel timer: Wait-to-Start input
Timed 15 , 30 ,45 seconds
11
Timer mode run time: 12 min
3, 6, 9, min
12
Timer mode: Timed starts
Temp starts
13
Short run (turbo): 1 min
3,5, 10 min
Remote Programming
1. Open a door
2. Turn key to the ON position
3. Within 5 seconds, press and release the control center button one time.
4. Within 5 seconds, press and hold the control center button. The LED will flash
one time and the siren chirps to confirm entry into remote programing.
5. Press the
AUX
button on the remote control.
6. The siren will chirp to confirm the remote has been programmed.
7. Release the control center button.
8. The siren will emit one long chirp confirming that remote programming has
been exited.
The programming routine exits if any of the following occurs:
The open door is closed
The ignition is turned off
There is no activity for 30 seconds
The control center button is pressed too many times
Basic Remote Functions
Button
Function
A U
X
ARM
A U
X
DISARM
AUX
AUX
REMOTE START
AUX
TRUNK RELEASE
Note:
See Owner’s guide for more details
Long Term Event History
The system stores the last two full triggers in memory. These are not erasable. Each
time the unit sees a full trigger, the older of the two triggers in memory is replaced by
the new trigger. To access long term event history:
1. With the ignition Off,
press
and
hold
the control center button.
2.
Turn
the ignition On.
3.
Release
the control center button.
4. Within 5 seconds,
press
and
release
the control center button. The LED flashes
in groups indicating the last two zones that triggered the unit for 1 minute or
until the ignition is turned off. Refer to table of zones.
Note:
The Warn Away triggers are not stored to memory and is not reported.
Table of Zones
A zone is represented by the number of LED flashes used by the system to identify a
particular type of input.
Zone
Trigger Type
Input Description
1
Instant Trigger
BLUE (H1/7)
2
Multiplexed Shock Sensor Input
Mux BLUE sensor port wire.
3
Door Trigger
GREEN (H1/8) and VIOLET (H1/6).
4
Multiplexed Shock Sensor Input
Mux GREEN wire
5
Ignition
Yellow ribbon harness wire
6
Hood Trigger
GRAY on the 6-pin shutdown harness
