background image

17

© 2011 Directed Electronics. All rights reserved.

6.  Turbo Mode

1.  No turbo Mode: Turbo mode is not available

2.  On – 1/3/5/10 minutes: Turbo Mode is available and, when activated, the engine will run for the 

duration set per the selected option

7.  Timer Mode Runtime

• 

12/3/6/9 minutes: sets the runtime when the engine is started by the Timer Mode and SmartStart 

features

 

8.  Flex Relay Function

1.  Ignition 2: the relay will emulate the Ignition 1 output during remote start

2.  Accessory 2: the relay will emulate the Accessory  1 output during remote start

3.  Starter 2: the relay will emulate the Starter output during remote start

9.  Diesel Start Delay

1.  Wait-to-start input: (-) input on the Grey/black (H2/20) WTS wire will delay the starter output until 

the ground ceases. 

2.  Timed 15/30/45 seconds: delays the starter output per the selected option, the WTS wire does not 

function.

10. Accessory during Diesel Start Delay

1.  On: the Accessory outputs (H3/3 high current and H2/22 low current) will be ON during diesel 

start delay

2.  Off: the Accessory outputs (H3/3 high current and H2/22 low current) will be OFF during diesel 

start delay

11. Status 2 Output (Blue/white H2/3 wire)

1.  Status: the output will activate before the ignition outputs turn on, and de-activate after they turn off 

during remote start 

2.  Latch rear defogger: the output activates 10 seconds after start if the interior temperature is below 

55F˚. It turns off after  10 minutes or upon remote start off 

3.  Pulse rear defogger: the output activates (for 800 ms) 10 seconds after start if the interior temperature 

is below 55F˚.

12. Parking Light Output

1.  Constant: the lights will turn on  solid during remote start

2.  Pulsed: the lights will pulse on/off during remote start

3.  Off: the lights will be off during remote start

13. Anti-grind Output

1.  On: the high current starter relay will be activated during remote start as anti-grind protection.

2.  Off: the high current starter relay will not be activated during remote start, no anti-grind protection 

is available.

14. Tach Mode Starter Release

1.  Normal: the starter output will release normally during cranking (50% of the learned tachometer 

value) 

2.  Increase: the starter output will release later during cranking (at 35% of the learned tachometer 

value)

3.  Decrease: the starter output will release sooner during cranking (at 35% of the learned tachometer 

value)

 

15. Vehicle Temp Auto Report

1.  Off: the report during remote start is defeated

2.  On: the report is sent every 2 minutes during remote start if the temperature has changed (+/-) 1 

degree since the last report 

16. Remote start Safelock

1.  Off: the Door lock and Factory Alarm Re-arm outputs will maintain the current status (locked/un-

Содержание Clifford 520.4X
























Отзывы: