Directed Electronics 556L, Руководство пользователя

Страница: 2 / 8

2 2
© 2005 Directed Electronics, Inc. Vista, CA
N556L 05-05
G GR REEEEN N//B BLLA ACCK K:: Not used for this application.
B BLLA ACCK K//W WH HIITTEE ((--)) o ou uttp pu utt tto o b bu ullb b cch heecckk w wiirree:: Connect this wire to
the 20-gauge BLACK bulb check wire in the ignition switch power
harness. This wire will test (-) ground only when the ignition
switch is turned to the crank position. Do not connect to the black
wire in the three-wire Passlock cable.
B BLLA ACCK K ((--)) P Paassssllo occkk g grro ou un nd d iin np pu utt:: Connect this input to the
Passlock system’s ground reference wire.
P PIIN NK K ((+ +)) iig gn niittiio on n iin np pu utt:: Connect this wire to the heavy gauge pos-
itive (+) PINK wire of the vehicle’s main ignition.
B BLLU UEE ((--)) ssttaattu uss iin np pu utt:: Connect this wire to the (-) status output
(BLUE/WHITE or BLUE) of the Directed remote start system.
V VIIO OLLEETT ((--)) iin np pu utt ffrro om m ssttaarrtteerr rreellaayy:: Connect this wire to the (-)
starter output of the remote start system. This is the VIOLET ribbon
harness wire of the pre-wired relay pack. To verify the correct wire,
test using a digital multimeter and verify that (-) chassis ground is
present on this wire while the remote start system is engaging the
starter motor.
R REED D ((+ +)) 1 12 2 vvo olltt iin np pu utt:: Connect this wire to a source of constant
12 volts. This wire has a 5-amp fuse.
W WH HIITTEE:: Not used for this application.
Y YEELLLLO OW W R R--CCo od dee,, iig gn niittiio on n ssw wiittcch h:: Connect this wire to the ignition
switch side of the resistance wire in the three-wire Passlock cable
in the vehicle.
W WH HIITTEE//Y YEELLLLO OW W:: Not used for this application.
B BLLA ACCK K//Y YEELLLLO OW W R R--CCo od dee,, o ou uttp pu utt tto o vveeh hiiccllee ssiid dee:: Connect this wire
to the side of the resistance wire facing away from the ignition
switch. This wire is located in the vehicle's three-wire Passlock
harness.
W Wiirree CCoonnnneeccttiioonn GGuuiiddee ffoorr PPaasssslloocckk II
.
GREEN/BLACK—(not used)
BLACK/WHITE—(-) bulb check
BLACK—Passlock ground
PINK—(+) ignition
BLUE—(-) status input
VIOLET—(-) crank input
RED—(+) 12V
WHITE—(not used)
YELLOW—key side resistance in
WHITE/YELLOW—(not used)
BLACK/YELLOW—vehicle side resistance out
HARNESS 1
HARNESS 2
PPaasssslloocckk II W Wiirriinngg DDiiaaggrraam m
The module must first be programmed before operation, use the
following procedure:
IIM MP PO OR RTTA AN NTT!! The vehicle must be started within 15
seconds or the module will automatically exit the learn
routine.
1. Cycle the ignition On/Off 2 times.
2. Start the vehicle and keep it running for at least 10-seconds.
3. The LED on the module will flash 2-times.
4. Wait for the LED to flash once very quickly (within 5-seconds)
of ignition On. The R-code is learned.
3. Programming is now complete. Turn the vehicle’s ignition off
and test remote start at least twice.
N NO OTTEE:: Refer to the end of this document for
troubleshooting procedures.10.
Programming is now complete. Reconnect starter wire.
Test remote start at least twice.
PPaasssslloocckk II PPrrooggrraam mm miinngg